TAGGED
Toy
14 designs tagged “Toy”.
Board games / Dice
Teetotum Set — Spinning-Top Dice (d6 · d8 · d10 · d12, 2-Colour)
The pre-dice gambling top, four ways: spin it, let it topple, read the up-facing number. d6/d8/d10/d12, each a 2-colour print with a modelled break-away support that peels off clean — no scars, no slicer supports.
Toys & mechanisms / Whistles
Beawhistle — beaver whistle, loud twin-chamber, one piece, no supports
A beaver standing on its tail with a chewed stick in its teeth that is also a loud pealess whistle: blow into the stick, the sound leaves two slots between its shoulder blades. Two stopped-pipe chambers of unequal length pulse against each other — measured on the printed part at 2205 Hz with a ~70 Hz warble, the Fox-40 architecture. 99 x 26 x 50 mm, one piece, print-in-place, no supports, no hardware.
Toys & mechanisms / Fidgets
Flexi Snake — print-in-place articulated fidget that coils
A print-in-place snake that prints in one piece, no supports, and coils into a full spiral in your hand. 16 necked vertebrae on captive ball-and-stalk joints, each folding 50-70 degrees, plus a carved head with eyes and scale rings. Fully parametric: dial the number of segments and their length right in the .scad.
Toys & mechanisms / Mechanical
Wand Through the Wall — a Straight Wand Passes Through a Curved Slit
A dead-straight wand on a little turntable swings clean through two CURVED slits in a wall, twice per turn, without bending. The wand is skew to the axis, so it sweeps a hyperboloid; the wall cuts that in a hyperbola, and that is the slit. Four flat supportless parts, formula engraved on the base.
Toys & mechanisms / Fidgets
Infinity Cube — Animal Fidget (folding magic cube, 48 engraved animals, two-colour)
A folding infinity cube (magic cube) fidget toy: eight cubelets linked so you can fold it end over end forever. Every one of the 48 faces carries a different animal silhouette. Prints fully assembled — the links are captured by the cube geometry, not glued — and the animals come as a separate inlay STL so you can print them in a contrast colour. Confirmed printed and everting on a real machine.
Toys & mechanisms / Mechanical
Jonah Whale - Press the Blowhole to Open the Jaw
A print-in-place whale toy. Press its blowhole and the jaw drops open to reveal a tiny diver.
Toys & mechanisms / Mechanical
Marble Run — Print-in-Place Roman-Greek Track
One-shot print-in-place marble run with a 3-pin plinko mid-section, sloped chute finish, and integrated Roman column supports. Greek-key meander engravings on all outer walls. Ships with a standalone start-hopper accessory + start/finish flag pair.
Toys & mechanisms / Whistles
Narwhistle — narwhal whistle, loud twin-chamber, one piece, no supports
A narwhal standing on its flukes on an ice floe that is also a loud pealess whistle: blow into the tusk, the sound leaves the blowhole. Two stopped-pipe chambers of unequal length pulse against each other — measured on the printed part at 2266 Hz with a ~66 Hz warble, the Fox-40 architecture. 102 x 40 x 31 mm, one piece, print-in-place, no supports, no hardware.
Boxes & storage / Catch-alls & coin banks
Piggy Bank 🐷 — top coin slot + finger-twist bottom plug
A classic chubby piggy bank: drop coins through the top slot (takes any circulating coin up to Ø33 mm), empty it by unscrewing the knurled bottom plug with your fingers — no tool. The pig prints as ONE belly-down body (snout, ears, curly tail, feet all integral) plus a separate twist plug. Watertight, no supports. Parametric OpenSCAD source included.
Toys & mechanisms / Mechanical
Pop-Up Toaster — Toy with a REAL Spring-Launched Pop
A pretend-play toaster that actually works: press the side lever DOWN and it clicks down and latches; push the side EJECT buttons and POP — both toast slices spring up out of the slots. Real printed coil springs and a self-engaging sear latch, just like a 1950s toaster. No glue, snap-together, kid-safe energy budget.
Kitchen / Drink Holders
Cup Holder Car — rolling toy coupe with a drink well in the roof
A chunky toy coupe whose roof is a real Ø73 mm drink well — decorative AND functional. The four wheels actually roll on captive snap-on axles. No glue, no supports, fully parametric OpenSCAD.
Toys & mechanisms / Mechanical
Lazy-Tongs Snapping Dragon — extending scissor grabber
A lazy-tongs scissor reacher themed as a dragon: squeeze the tail and the neck telescopes out while the head snaps shut — one motion, one moving mechanism.
Outdoors / Beach Games
Beach Ring-Toss Lawn Game — Scoring Target Board + Tossing Rings (sand-resting, no stakes)
A beach/garden ring-toss set: a flat sand-resting target board studded with 9 scoring pins (centre = 3 pts, 3 inner = 2 pts, 5 outer = 1 pt) plus chunky two-team tossing rings. Toss a ring underhand so it drops over a pin to score. Print two boards and set them a few metres apart. Fully parametric OpenSCAD — every diameter, height and ring size is a variable. Prints flat with no supports.
Outdoors / Sand Play
Beach Sandcastle Kit — 8-Piece Mould & Tool Set (castle buckets + sieve, rake, shovel, tamper)
A complete kids' beach sandcastle kit: 3 stacking castle bucket-moulds (keep, tower, great hall) plus 5 sand tools — a perforated sieve-scoop, a rake, a shovel, a tamper and a detailing tool. Pack the wet sand into a mould, lift, and decorate with the tools. All parametric OpenSCAD, prints flat with no supports.