TAGGED
No supports
134 designs tagged “No supports”.
Bathroom / Makeup organizers
Apothecary Brush Drying Rack — hangs brushes bristles-down
A rack that dries makeup brushes the way every brush-care guide says to dry them: hanging HEAD DOWN over a drip tray. A brush stood bristles-up runs water into the ferrule, the glue softens and the brush sheds — this is the one makeup problem with a real failure mode behind it, and nothing prints a rack that fixes it. The grip is a WEDGE SLOT, not a hole: handles run about 6–12 mm and no single bore fits them, so each of the six slots tapers 13 → 5 mm over 22 mm and every brush catches at its own diameter, at about 9.4° per side, well inside PLA's friction angle. 172 mm of measured hang clears a 190 mm brush. The rail lifts straight off the two posts to load, and the tray is then a plain open dish you tip and rinse. 2 parts, 176 × 78 × 219 mm, 301 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Cauldron Makeup Organizer — a bowl with no corners, no supports
A three-legged cauldron that sorts makeup, and the bowl is the whole idea: it is a truncated sphere, so there is no corner anywhere inside it for powder to pack into. A 2.6 mm wall runs into a 3 mm floor through a 4 mm fillet rather than a crease, and one wipe reaches every part of the inside. Brushes stand in it bristles-up and fan out against the curve; a 4-way cross drops in to quarter the bowl for jars, sponges, compacts and hair ties, and lifts out to leave a plain brush cup. The three legs are a separate trivet ring the bowl drops into on a 45 degree cone, because legs cast under the bowl print as a horizontal overhang between them. 3 parts, 92 x 90 x 77 mm assembled, 117 g, no supports, no hardware, no glue — assembly is dropping one part into another.
Bathroom / Makeup organizers
Dragon Wing Palette Rack — eyeshadow palettes on edge, no supports
An eyeshadow-palette rack whose fins are the finger bones of a dragon wing. Palettes stand on edge like books, so you read the spines and pull one out one-handed instead of excavating a stack. Five 16.5 mm slots take anything up to an 18 mm palette, with 100 mm of clear depth between the front rail and the back spine and a 76 mm shortest fin. Every segment of the fin profile is upward-facing, so a 112 mm tall part prints with ZERO supports. 1 part, 118 x 128 x 112 mm, no supports, no hardware, no assembly.
Bathroom / Makeup organizers
Frost Crystal Casket — makeup organizer, no supports
A block of glacier ice with a quartz cluster growing out of the back, and the cluster is the working part: all seven crystals are bored straight through, so a brush pushed into a shard stands bristles-up while its handle hangs in the box below — which is why a 120 mm and a 220 mm brush end up standing at the same height. Bores are cut to measured stock: Ø27 for mascara, two Ø23 that neck down to Ø14 so a lipstick rests on the shoulder, and four brush bores at Ø16 and Ø11. There is not one blind hole in the model and the well underneath is a single cavity with a 4 mm cove where the floor meets the wall, so nothing has a square corner to pack powder into. 3 parts, 132 × 114 × 100 mm, 298 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Great Helm Makeup Organizer — knight's helm, no supports
A 13th-century flat-topped great helm that is a makeup organizer on the inside. The crown is open and a lift-out liner drops onto the rim carrying the whole bore field, so brushes stand out of the helm like a crest: six brush bores go straight THROUGH so the handle hangs in the cavity and a 120 mm and a 220 mm brush stand at the same height, three tube bores (Ø27 mascara, two Ø23 lipstick) neck down instead of bottoming out, and an 88 × 24 mm palette slot rests a compact on an open 8 mm ledge. Not one bore is blind, so powder falls through into a smooth drum you tip out and rinse. 2 parts, 134 × 125 × 150 mm, 307 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Medieval Well Makeup Organizer — no supports
A stone draw-well with a winding gantry, a gable roof and a bucket on a string — and a makeup organizer inside it. The coping stone is a lift-off plate carrying all 11 bores, and not one of them is blind: a brush handle hangs free down the shaft, a mascara rests in a 45° seat cone instead of bottoming out, and loose powder falls straight past into a rinse dish in the plinth. Cleaning is lift, lift, tip, rinse. 5 parts, Ø144 × 176 mm, 420 g, no supports, no hardware, no glue — just ~120 mm of twine for the bucket.
Bathroom / Makeup organizers
Moonwake Makeup Wardrobe — a 240 mm two-door cabinet with printed hinges and lift-off door bins
A 240 x 200 x 228 mm cabinet for makeup and hygiene: two engraved doors on four printed pins that swing to 160 degrees, four lift-off bins on the door panels, and two removable organizers inside for brushes, tubes and palettes. 13 parts, no hardware, no glue, no supports.
Bathroom / Washing & personal care
Q-tip Cup — Fluted Cylinder with Snap-Fit Lid
Ø69 × 60 mm fluted cup that holds ~250 standard cotton swabs, with a faceted gem-top lid that snaps on with an audible click. Doric-style vertical flutes (24 concave grooves) on the cup, octagonal gem dome on the lid. Two STLs, prints flat, no supports.
Bathroom / Makeup organizers
Tenshu Makeup Organizer — Japanese castle keep, 3 lift-off storeys
A Japanese castle keep (tenshu) that sorts makeup. Every roof is the lid of the storey under it: the base holds four compacts on edge in a lift-out comb plus a polish bay, the second storey has three coved lanes for a mascara, lipsticks and pencils lying down, the third a tweezer lane and two cells for lashes, pins and rings. Every pocket is a hull of four spheres, so the floor meets the wall on a 4 mm cove and nothing is a square corner or a blind hole: lift, lift, lift, tip, rinse. Five parts, no supports, no glue, no hardware — each lid seats on a 2.4 mm ring so the stack does not rock, and magnets are an option, not a need. Ships as one-colour STLs and, for a multi-filament printer, as one three-colour STL per part that Split to Parts divides into exactly three: cream plaster, dark timber, slate stone-and-tile. A five-colour split-to-parts STL per part ships too, if you have the slots for a separate plinth grey and gold shachihoko.
Bathroom / Washing & personal care
Toothpaste Tube Squeezer — Roller Key, Diamond-Knurl Grip
Single-piece roller key for toothpaste / cosmetic tubes. Slot the empty end of the tube through the slit, fold once, twist the body — the tube wraps around the bar and you crank every last gram out. Hang hole at top. Diamond-knurl engraving on both faces for grip.
Bathroom / Makeup organizers
Wizard Tower Makeup Organizer — 4 lift-apart tiers
A wizard's tower that sorts makeup. Brushes hang bristles-up from five wedge bores through the roof cone, so each one catches at its own handle diameter and a 120 mm and a 190 mm brush stand at the same height. The balcony deck takes a mascara, two lipsticks and three pencils; the plinth is a deep open bin for polish and jars. Every one of the eleven openings is a THROUGH hole and the bin floor is coved into the wall, so powder falls through instead of packing into a blind corner: the tower lifts apart into four pieces you tip and rinse under a tap. No supports, no glue, no hardware — every joint is a triangular tongue that drops into a V-groove.
Board games / Find your game / Cascadia
Cascadia Market Rack + 3D Wildlife Tokens
A two-in-one Cascadia upgrade: a market-row display rack that holds the four face-up habitat tile + wildlife token pairs on a gentle 15° slope, PLUS a full set of five sculpted 3D wildlife tokens (bear, elk, salmon, hawk, fox) that replace the flat wooden discs and drop straight into the rack's Ø19 cups. The rack prints flat and supportless in one part; each animal prints upright on a Ø18 base disc in its own colour — no AMS, no paint. Parametric OpenSCAD source included.
Board games / Classic games / Cribbage
Travel Cribbage Peg Track — Captive Slide-In Pegs, 1 to 6 Players
A pocket cribbage scorer with captive scoring pegs that can never fall out. Each player's peg rides a hidden T-channel and clicks into every score station on a self-centring ball-detent, so it always lands exactly on the number. Slide the pegs into the open end, snap the end cap on, and they are enclosed for good. One parametric design, bundled in every player count from 1 to 6.
Board games / Find your game / Dungeons & Dragons
Adventurer Dial Base — a mini base that counts your damage 0–9
A Ø36 mm miniature base with a rotating 0–9 counter ring built into it. It prints in place: the disc and the ring come off the plate already interlocked, no assembly, no hardware. A hooded wanderer figure is included — drop it in, or print the version with it welded on.
Board games / Find your game / Dungeons & Dragons
D&D Death Save Tracker — slide up for a heart, down for a skull
A flat, silent death-saving-throw tracker for D&D 5e. Three captive sliders: push one UP and a red heart fills the top window (success), push it DOWN and a white skull fills the bottom one (failure), leave it centred and both stay blank. Three hearts you're stable, three skulls you're dead — the whole table can read your state from across it. Five printed parts, no glue, no screws, no dice-sized bits to lose; everything prints flat and supportless. Parametric OpenSCAD source included.
Board games / Find your game / Frosthaven
Cassandra Rift Overlay Hex Tokens — Frosthaven / Gloomhaven (3-colour, a mini stands on it)
3D rift overlay hex tokens for Cassandra the Forgotten Diviner (Frosthaven / Gloomhaven). Each is a 38.1 mm flat-top map hex with a recessed flat central plaza a mini can stand on, ringed by a raised ornate runic frame. Three-colour AMS print: dark stone body, a magenta energy vortex flush in the plaza floor, and gold raised runes on the frame. Prints support-free — every feature steps up. Includes a fit-test coupon and the parametric OpenSCAD source.
Board games / Find your game / Frosthaven
Ghost Falcon Summon Standee with Life Dial — Frosthaven
A 37.5 mm hex standee for Cassandra's Ghost Falcon summon. The captive ring turns to show 1–4 life; the pedestal shows 2 damage, 4 health and 3 movement. One print, no assembly.
Board games / Find your game / Catan
Catan Replacement Set — Settlements, Cities, Roads, Knights, Ships & More
Hand-sculpted replacement set for Catan + Cities & Knights + Seafarers + Traders & Barbarians. 15 pieces: textured cobblestone road (thin/half/full), gabled cottage settlement, cityhall + crenellated brick wall ring, hooded robber, three escalating C&K knights (basic/strong/mighty), C&K barbarian + merchant, Seafarers galleon ship + tricorne pirate, T&B recumbent caravan camel. All silhouettes designed to print supportless on FDM.
Board games / Dice
Crooked Dice — a fair die, a gaff die and a loaded die that look identical
Three 16 mm d6 from one source: an honest die, a duplicate-face gaff showing only 5 and 6, and a die with a sealed void under the 6. Same body, same size, same weight to within a tenth of a gram. Ships the float-test cup that catches the loaded one, and states how crooked each die is as a measured number instead of an adjective — centre-of-mass offset and tipping-barrier ratio for all six faces. A magic and party prop, sold with its own counter-measure.
Board games / Classic games / Dominoes
Domino Box — Sleeve + Tray for the Double-Six 28-Tile Set (OpenSCAD)
Two-piece storage for a full 28-tile double-six domino set. Outer sleeve (closed on 5 faces, open on one short end) + inner tray with a Ø28 mm semicircular thumb-notch on its front wall. Tiles lie flat in a 4×2 grid of 4-tile stacks (32-slot capacity). Sleeve prints with the open mouth UP — fully supportless. Engraved decorative pip pattern on every long face. Parametric SCAD lets you re-tune tile dimensions, slop, layout (piles_x × piles_y), pip pattern, or wall thicknesses.
Board games / Original games
Dragon's Nap — a co-op heist board game round a sleeping dragon, all printed
A co-op heist for 1-4. Lift gems from under a sleeping dragon whose head really turns, and get out before it wakes.
Board games / Accessories / Dice Storage
Mimic Vault — dice drawer in a monster that eats the loot
A ruined stone monument that's secretly a mimic: the front drawer is its maw and slides out to reveal your 7-die set, relief teeth grin under a translucent crystal bait pile on top. Prints upright, no supports. Includes a matching two-colour D6 with bone-femur Roman numerals.
Board games / Original games
The Older Current — a board game for PlayGrid
A complete 2-4 player strategy game on the PlayGrid grid — board, 100 tiles, 12 figures and a box, all included. You never move your own people; you re-aim the current that carries them.
Board games / Dice
Pasa — Indian long dice, the d4 you can actually roll
A long die: a square rod marked on its four long sides and capped at both ends so it can never stand up. You roll it like a pencil and read the number on top. Ships the traditional Chaupar/Pachisi stave (faces 1-2-5-6) and a plain 1-2-3-4 version, each in one colour and as a two-colour Split-to-Parts file. 62 x 10 x 10 mm, flat on the bed, no supports. The opposite-face pairing is chosen to MINIMISE bias, not to sum to seven — 4.1x less centre-of-mass offset, and the two-colour build cancels it entirely.
Board games / Dice
Pumpkin d6 — Every Pip Is a Pumpkin, the 1 Is a Jack-o'-Lantern
A standard 20 mm six-sided die where all 21 pips are little pumpkins and the lone 1 is a carved jack-o'-lantern. Prints in two colours from a single STL — import, Split to Parts, done. No supports, no brim.
Board games / Dice
Emoji Reaction Die — a mood d6 that replaces the RPG reaction roll
One 18 mm d6 with six emoji faces on a HOSTILE → HELPFUL ladder. Roll it when the party meets an NPC and read the attitude straight off the top face — no 2d6 lookup table, no maths. Opposite faces hold opposite attitudes. Three interchangeable face styles in the box (geometric, emoji-glyph, cartoon) and every style ships as a two-colour combined STL with the faces as flush inlays, plus a single-colour version with paint-fillable recesses. Prints on any face, no supports.
Board games / Original games
The Answering — a co-operative board game for PlayGrid
A complete 1-4 player co-op game on the PlayGrid grid — 28 figures, 17 tiles, a die and its tower, all included. The swarm never takes a turn of its own. It answers yours.
Board games / Original games
Watchfires — a stacking board game of beacons for 2–4, all printed
A stacking game of beacons for 2-4. Every ring you place is a watchman who counts the towers he can see.
Board games / Find your game / Magic: The Gathering / Counters
MTG — Amass Army Dial (0–15, goblin knob)
A two-part rotating counter for a single growing Army token. Only ONE number is ever visible, through a window in the fixed cap, so it reads like a tally slate rather than a clock face. Thumb on the goblin holds the cap, fingers turn the scalloped rim, every number lands with a detent click. Two printed parts, no glue, no hardware, no supports.
Board games / Find your game / Magic: The Gathering / Counters
MTG — Mana Barrel Counter (3-Drum Hex Dial)
Three-digit (0-999) rotating barrel counter for Magic: the Gathering — hex prism with three independently-rotating drums, capped at each end by a hex cap engraved with the chosen mana symbol (W/U/B/R/G or colourless). Caps lock to a shared square axle so the drums rotate but the caps don't. Engraved digits + mana symbols print as 2-AMS Bambu Split-to-Parts. ~50 mm tall, no supports, PLA.
Board games / Find your game / Magic: The Gathering / Counters
MTG — Creature Token Tracker (P/T Wheels + Type & Ability Tiles)
A card-side dashboard for tracking a single Magic: the Gathering creature token. Two flat 0–9 spin-wheels show Power / Toughness; a row of side-loading tiles behind them name the creature's TYPE and its keyword ABILITIES. Includes the token chassis + snap-on lid + two-colour digit wheel, a storage box with engraved mana-symbol lid, and the full set of 47 creature-type tiles and 42 keyword-ability tiles. Engravings print as 2-AMS Bambu Split-to-Parts, or single-colour. No supports; print the token chassis + lid in PETG (the snap pins), everything else in PLA.
Board games / Find your game / Magic: The Gathering / Tokens
MTG — Day / Night Flip Token (60mm Disc)
60 mm two-sided flip token for the Day/Night mechanic in Magic: the Gathering. Sun (with 12 radiating rays) on the day face; crescent moon + 3 stars on the night face. Flip the token whenever a card transitions Day↔Night so the current state is always visible. Two-colour AMS print: dark body + gold engravings.
Board games / Accessories
Eiganjo Castle Commander Deck Box
A support-free 100-card Commander deck box with a removable two-colour Japanese castle on its snap-fit lid.
Board games / Find your game / Magic: The Gathering / Tokens
MTG — Food · Blood · Clue Artifact Token Set
A set of three 3D artifact tokens for Magic: the Gathering, replacing the cardboard punch-outs: FOOD as a realistic lattice pie, BLOOD as a faceted gem-cut drop, and CLUE as a detective's magnifying glass. Each token prints flat, supportless, in one colour (or paint the details). ~22–30 mm, PLA. Parametric OpenSCAD source included.
Jewelry & accessories / Sewing buttons
MTG Mana Buttons — all six mana symbols as real sewing buttons, 15 / 20 / 25 mm, hidden shank or 2-hole
Wearable sewing buttons carrying all six Magic mana symbols — white sun, blue drop, black skull, red fireball, green tree and the colorless lozenge. 30 STLs: 6 symbols x 5 size/style combos. The 'tunnel' style hides a thread shank in the underside so the face stays whole and nothing is bored through the emblem; the 'holed' style is a classic 2-hole shirt button with both bores in the plain ring. Ø15 / 20 / 25 mm (24L / 32L / 40L). Every button ships a named-solid 2-colour companion for AMS. Prints flat, face up, no supports, no brim, no hardware. Fully parametric OpenSCAD — any diameter, and the glyph strokes are held at or above one nozzle width automatically.
Board games / Find your game / Magic: The Gathering / Tokens
MTG — Pact Reminder Token (YOU WILL PAY Scroll)
Medieval-scroll reminder token for Magic: the Gathering. Drop in front of an opponent who owes you a Pact upkeep (Pact of Negation, Slaughter Pact, Intervention Pact, Pact of the Titans, Summoner's Pact) or anyone trying to skip a delayed cost. 55×80 mm slim slab with raised parchment-roll ridges top + bottom and 'YOU WILL PAY' in raised medieval lettering. Two-colour AMS print: parchment body + ink letters.
Board games / Find your game / Magic: The Gathering / Counters
MTG — +1/+1 Counter Die (d6, +N/+N Faces)
A 16 mm six-sided creature counter die for Magic: the Gathering. Each face engraved with +N / +N (power / toughness) — values 1 through 6, opposite faces sum to 7. Two-colour Bambu AMS print: dark body + bright '+N' digits via Split-to-Parts.
Board games / Find your game / Magic: The Gathering / Tokens
MTG Powerstone Token — Flip-to-Tap Crystal
Chunky 60 × 30 × 16 mm faceted crystal token for Magic: the Gathering's Powerstone artifacts. It rests flat on either octagonal face: plain side up is untapped, tap-arrow side up is tapped. Flip it instead of rotating it. Prints as one part with no supports.
Board games / Find your game / Magic: The Gathering / Counters
MTG — The Ring Tempts You Tracker (Barad-dûr Plaque)
Two-piece tracker for the LotR Ring mechanic. Tower-of-Sauron silhouette plaque with 4 detent pockets (Levels I–IV) + ability label inset beside each in a second filament colour, plus a small One-Ring marker that the active player places in the current level. ~130 mm tall, prints flat, no supports. Bambu AMS 2-colour: dark body + gold labels.
Board games / Find your game / Spirit Island
Spirit Island Blight Tokens, Sculpted Dead Tree (Multicolour)
Spirit Island blight as a small sculpture: a charred dead tree on grey ash with red cracks, a skull and bones, printed complete in four colours with no supports.
Board games / Find your game / Spirit Island
Spirit Island Defend Tokens (Multicolour, Stackable)
Defend 1, 2 and 4 shields for Spirit Island, printed complete in two colours with no supports, and nesting so a stack stays put.
Board games / Find your game / Spirit Island
Spirit Island Fear Tokens (Multicolour)
One-fear and five-fear tokens for Spirit Island, printed complete in three colours with no supports: a skull over crossed bones, and a cairn of five skulls.
Board games / Find your game / Spirit Island
Spirit Island Invaders — four-colour explorer, town and city, no supports
Full set of multicolour invader pieces for Spirit Island: a colonist explorer in a tricorn hat, a half-timbered town and a guild-hall city with a clock tower. Each piece prints complete and coloured in one go, no supports, no glue. Ready plates with the filaments already assigned.
Board games / Find your game / Spirit Island
Spirit Island Branch & Claw / Jagged Earth Tokens (Multicolour)
Beasts, wilds, disease, badlands and strife tokens for Spirit Island, printed complete in 3-4 colours with no supports and the game icon underneath.
Board games / Find your game / Spirit Island
Spirit Island Nature Incarnate Tokens (Multicolour)
Vitality, deeps, quake and incarna tokens for Spirit Island Nature Incarnate, printed complete in four colours with no supports and the game icon underneath.
Board games / Find your game / Spirit Island
Spirit Island Scenario Markers, Sculpted Figures (Multicolour)
Sculpted multicolour markers for six Spirit Island scenarios and the Habsburg Livestock Colony damage, printed complete with no supports.
Board games / Find your game / Terraforming Mars
Terraforming Mars Track Figures — Biodome, Reactor, Rover
Three sculpted markers for the Terraforming Mars tracks: a greenhouse biodome for oxygen, a fluted cooling tower for temperature and a six-wheel rover for generation. Each is one solid print on a Ø12 mm base, upright with no supports, no assembly and no hardware — about 2.2 g of PLA for the whole set. Print one filament per figure; they replace the game's ordinary markers on its existing printed tracks.
Board games / Find your game / Wingspan
Wingspan Card Holder — 3 Slots, Bird Silhouettes
3-slot tilted-back card holder for Wingspan bird cards (or any 55×90 mm sleeved card). Each cell has a different bird silhouette (kiwi / sparrow / eagle) on its back wall — revealed when the card is removed.
Board games / Find your game / Wingspan
Wingspan Dice Nest Tray — Twig-Clad Bird's Nest Dice Tray
Dice tray for Wingspan (or any tabletop game) shaped like a woven bird's nest outside, rectangular cavity inside. 600 randomly-placed twig cylinders, no supports, no hardware.
Board games / Find your game / Wingspan
Wingspan Twigs Nest — Stadium-Shaped Bird's Nest Dice Tray
Shallow stadium-shaped dice tray for Wingspan (or any board game) shaped like a real woven bird's nest. ~1100 procedural perimeter twigs sweep continuously around the perimeter; ~800 short pillars in the saucer interior recreate a pebble/twig floor texture. No supports, no hardware.
Boxes & storage / Keepsake boxes / Fantasy
Library of Alexandria box — a magnetic box under the great dome
The Library of Alexandria as a box: a white-marble hall behind an arcade of pointed arches, a full-width stair, four turrets under gilded onion domes and a great ribbed dome on a chevroned drum. Everything above the cornice is the lid, and eight Ø5 × 3 mm magnets buried mid-print hold it shut. 118 × 96 × 113 mm outside, 90 × 60 × 45 mm inside. Six STLs, two prints, no supports, no glue.
Boxes & storage / Organizers / Baskets
Honeycomb Hinged Storage Box — Large (PIP, 3 sizes)
Big rectangular storage box with hex pattern on every wall + print-in-place piano hinge — prints OPEN, snaps shut, no assembly. Three sizes bundled.
Boxes & storage / Organizers / Drawers
Carousel Drawer Tower — Stacking Swing-Out Parts Organiser
A modular desk organiser of pie-wedge bins that swing out around a central post. Stack as many tiers as you like; a wide fillable ballast dish keeps it planted. Fully parametric OpenSCAD.
Boxes & storage / Keepsake boxes / Fantasy
Castle keep box — a fortified keep that opens at the wall-walk
A 112 mm square castle keep whose lid is the wall-walk: lift the battlements, four corner drums and their tiled conical roofs straight off and the keep is a 70 x 70 x 64 mm box. Two prints, no supports, no hardware, nothing to glue. The lid rests rather than latches, so it is a table box, not a travelling one. Multi-colour for the AMS, and it still reads as a castle in one filament.
Boxes & storage / Keepsake boxes / Nature
Coffee Bean Box — Bean-Shaped Trinket Box (2 Parts, No Supports)
A little lidded trinket box shaped like a coffee bean, crease and all. Two printed parts, friction-fit lip, no supports, no hardware. 82 × 50 × 21 mm closed.
Boxes & storage / Lunch Boxes
Composition Book Lunchbox — a snack caddy shaped like a school notebook
A 150 x 105 x 52 mm lunch/snack caddy that looks like a marbled composition notebook. Print-in-place-style pin hinge (the pin prints too), no hardware, no supports, no glue. Three parts, three colours, and the colour split costs about 1.4 g of purge for the whole set.
Boxes & storage / Keepsake boxes / Fantasy
Elven Motif Keepsake Box — vesica plan, interlaced vine walls, two-colour leaf inlay
A pointed-oval trinket box where every ornament is the same shape at three scales: the box plan, the leaves woven into the wall braid, and the veined leaf inlaid in the lid. The wall vine is a genuine over-and-under interlace, not two sine waves. Two printed parts, no supports, no hardware, no glue — and the two-colour lid costs about 1 g of purge because all the ink sits in three layers.
Boxes & storage / Keepsake boxes / Fantasy
Elven seed archive — four-colour drawer box, pinned roof, no glue
Four-colour elven drawer box, 240 x 200 x 70 mm closed, with a scalloped leaf roof, arched tracery windows and a full-width pull-out drawer. Three prints plus four friction pins, no glue, no supports, no hardware.
Boxes & storage / Keepsake boxes / Fantasy
Grimoire Box — a hinged spellbook with the magnets sealed inside
A leather-bound tome that opens on a real barrel hinge. Two sizes, any word you like on the cover, and four magnets that end up fully enclosed in the plastic - nothing visible in any face. Three printed parts, no supports, no screws, no glue.
Boxes & storage / Keepsake boxes / Geometric
Heart Trinket Box — Friction-Fit Lid (Two Fits)
A little heart-shaped box with a plug-in friction-fit lid. Two lid versions included — a relaxed fit and a firmer one — so you can pick how tightly it holds. Fully parametric OpenSCAD source.
Boxes & storage / Organizers / Baskets
Lattice Basket — Parametric Desk Organiser
A 15 × 10 × 5 cm open-lattice basket with 45° crosshatch walls, solid corner columns, and a flat rim. No supports needed.
Boxes & storage / Organizers / Baskets
Parametric Stackable Storage Box (1×1 to 5×5)
Stackable storage drawers with stud-and-hole interlock — they tile sideways and stack vertically with each other. 25 ready-to-print sizes from 1×1 up to 5×5, with both door orientations for every rectangle, plus 2 height/fit specials. Parametric SCAD source included — change pitch, height, or footprint to derive any size you want (the SCAD goes well past 5×5).
Boxes & storage / Keepsake boxes / Fantasy
Mead hall box — a Viking longhouse whose whole roof lifts off
A 199 mm Viking longhouse whose whole shingled roof lifts off, leaving a 177 x 83 x 31 mm box with the hollow roof above it. Two prints in one wood-fill filament, no supports, no hardware, nothing to glue. Every plank, knot and shingle is cut and jittered from one seed, so it reads hand-built. The roof rests on a tongue, it does not latch, so it is a table box, not a travelling one.
Boxes & storage / Keepsake boxes / Fantasy
Pirate treasure chest — print-in-place hinged trinket box, two colour
A 100 mm barrel-top pirate chest that comes off the bed as one working unit. The piano hinge prints in place, so there is no assembly, no pin to fit and no glue. Two-colour for the AMS: wood planks plus iron straps, banding, corner brackets, lock plate and hasp.
Boxes & storage / Keepsake boxes / Nature
Pumpkin Box — Realistic Two-Colour Lidded Pumpkin, Holds a Ø80 × 70 mm Jar
Ten-lobe pumpkin box, 131 mm wide, sculpted lobes and a gnarled green stem. Lid lifts off at the shoulder; the body swallows an 80 mm jar or candle. Two colours in one lid file, no supports. The lobes are uneven, so the lid matches the body in one rotation only.
Boxes & storage / Keepsake boxes / Geometric
Rhombic Dodecahedron Box — one part printed twice, magnets sealed inside
A 64 mm rhombic dodecahedron that opens at its equator. ONE STL, printed twice — the halves are congruent, not mirrored. Eight Ø4×2 magnets are enclosed mid-print: no glue, nothing visible, nothing to fall out. Stacks like cannonballs.
Boxes & storage / Keepsake boxes / Fantasy
Renaissance castle box — inspired by Rosenborg, the whole castle lifts off a hidden tray
A 240 x 108 x 250 mm Dutch Renaissance castle, inspired by Rosenborg in Copenhagen but not a 1:1 replica, that is a box: the whole four-colour castle is one print and lifts off a hidden tray. Almost three days of printing with a four-slot automatic filament changer. No supports, no hardware, no glue.
Boxes & storage / Keepsake boxes / Nature
Rut Box — a keepsake box locked shut by two stags' antlers
A 108 x 62 x 84 mm hunting keepsake box with a 64 ml cavity. Four antler racks — two on the base, two on the lid — interleave when the box is closed, like two stags with their horns locked in the rut. A quarter turn sweeps the racks apart and releases a bayonet lock. No hardware, no supports, no glue.
Boxes & storage / Organizers / Baskets
Stackable Lattice Basket — 4 Sizes + Parametric SCAD
Cross-stackable lattice baskets with cone-peg corner posts — any basket stacks onto any other basket. Four ready-to-print sizes from 5×5×5 cm cube up to a 20×12×8 cm tray, plus an optional cone-foot leg accessory. One open short side per basket so you can reach contents while the stack stays put. Parametric SCAD included — override basket_l/basket_w/body_h to derive any size; corner-post + peg geometry is shared so derived sizes still cross-stack with the printed ones.
Desk & office / Electronics / Stands
Stackable Server Rack — Tool-Free Mini-PC / NUC / SBC Shelf
A modular, tool-free rack for mini-PCs, NUCs, SBCs and other small servers. Each level is a honeycomb-vented floor on four fat corner posts; levels self-stack on cone pegs (no screws, no hardware) and four wide feet lift the whole tower off the desk for airflow. Print one floor per device, four feet once, stack as tall as you like. Parametric SCAD — resize for any box.
Boxes & storage / Keepsake boxes / Fantasy
Sugar Skull Box — Calavera Trinket Box (2 Parts, No Supports)
A Day-of-the-Dead calavera trinket box that splits at the brow — the cranium lifts off as a lid. Two printed parts, slip-fit lip, no supports, no hardware. 62 × 58 × 74 mm closed, ~37 cm³ inside. Optional AMS two-colour inlay.
Boxes & storage / Organizers / Baskets
Truchet Bucket Box — 5-Compartment Organizer with Maze-Pattern Walls
A lidless 5-bucket organizer with a flowing Truchet-tile maze pattern engraved on all four walls. Great for beads, hardware, ball bearings, craft bits. No supports, prints flat. Fully parametric OpenSCAD source included — change bucket count, size, or pattern.
Boxes & storage / Keepsake boxes / Geometric
Bayonet Tube — Ø50 × 60 mm with Quarter-Turn Locking Caps
Cylindrical tube container with two IDENTICAL bayonet caps. Drop a cap on either end, push, twist 35°, locked. No hardware, no supports. Parametric OpenSCAD source included.
Boxes & storage / Keepsake boxes / Fantasy
Tudor house box — half-timbered town house whose upper storey lifts off
A 184 x 214 x 150 mm half-timbered Tudor town house that is a box: the jettied upper storey, twin-gabled tile roof and chimney lift off as one lid over a 164 x 194 x 90 mm cavity. Two prints, nine coordinate-locked colour solids, no supports, no hardware.
Jewelry & accessories / Pendants
Amber Mosquito Pendant — Mosquito Suspended Inside a Translucent Lump, 2-Colour, No Supports
A mosquito embedded inside a lump of translucent 'amber'. Two filaments, no cavity and no glue — the insect is a second solid that the slicer prints inside the first. 33 x 30 x 7.5 mm, Ø3.5 bail, prints flat with no supports. Honest warning: the inclusion reads softly, and best when the pendant is held against the light.
Jewelry & accessories / Earrings
Antler Drop Earrings — Red Deer Rack
A red-deer rack shrunk to a 26 mm drop earring. Mirrored left and right pieces, flat on the bed face-up, no supports, 0.44 g each. Ø2.5 mm bore already sized for a 4 mm jump ring.
Jewelry & accessories / Earrings
Mini Anvil Earring — 3D Blacksmith Anvil Charm
A tiny London-pattern anvil earring, modelled fully in the round — tapered horn, overhanging working face, waisted body and spread base — with a pierced heel eye for a jump ring. Prints supportless on its side. Parametric OpenSCAD source included.
Jewelry & accessories / Earrings
Baroque Pearl Hoop Earring — Print-in-Place Sliding Pearls
A hoop earring strung with six irregular baroque pearls that really slide around it — printed in one piece, no assembly, no supports, no jump rings between the parts.
Around the home / Hooks
Bat Ceiling Hook — hangs by its own feet, head down, like a real bat
A roosting bat that hooks over a ceiling hook by its two toe-rings and gives you two open claw hooks at the bottom for cords, string lights or a planter. One part, no supports, no assembly.
Toys & mechanisms / Whistles
Beawhistle — beaver whistle, loud twin-chamber, one piece, no supports
A beaver standing on its tail with a chewed stick in its teeth that is also a loud pealess whistle: blow into the stick, the sound leaves two slots between its shoulder blades. Two stopped-pipe chambers of unequal length pulse against each other — measured on the printed part at 2205 Hz with a ~70 Hz warble, the Fox-40 architecture. 99 x 26 x 50 mm, one piece, print-in-place, no supports, no hardware.
Decorations / Coasters
Biohazard Coasters — raised trefoil that lets go of a wet glass, plus caddy
Ø90 mm coaster set with the biohazard trefoil standing 0.8 mm proud of the drink face, so a cold wet glass rests on three lobes and never suctions to the floor. Two-colour AMS file with the six-island mark pre-welded into ONE part, a single-colour version, and a stacking caddy for four. No supports.
Toys & mechanisms / Mechanical
Climbing Monkey — Classic Rope-Climbing Pull Toy
Pull the two beads alternately and the monkey ratchets up the cords toward his banana — let go and he stays put, slacken both cords and he slides back down. No springs, no glue, no mechanism to assemble: pure capstan friction through 45° paw channels. 3 printed parts + string. Prints flat, no supports. Kid-safe: Ø33 mm beads pass the choke gauge.
Decorations / Planters
Cyclo Planter — Vietnamese xích lô succulent pot that rolls
A Vietnamese cyclo (cycle rickshaw) as a small rolling planter: the passenger seat is the pot, the footboard is the drip tray, the driver's rack holds three cups for cuttings. 9 STLs, 16 press-fit pieces, no glue, no supports, no hardware. Wheels spin, cranks snap on, the hood bow doubles as a trellis. Printed and assembled — full illustrated guide below. Designed from scratch in OpenSCAD for the Custom Cyclo Challenge.
Decorations / Magnets
Deathly Hallows Fridge Magnet
The three Deathly Hallows as a slim fridge magnet — Cloak triangle, Resurrection-Stone circle, Elder-Wand line. Three Ø5×3 mm magnets are sealed invisibly inside the rounded corners during a single print pause: no glue, no exposed metal, either face sticks to the fridge.
Jewelry & accessories / Earrings
Dendrite Lace Earrings — Every Seed Grows a Different One
A generative lace-disc earring. The web is grown by a seeded random algorithm, so changing one number in the source gives you an earring nobody else has. Two structures included (crazed-glaze and coral), both 27 mm, both print flat with no supports in about 20 minutes. Print the same file twice for a matched pair.
Jewelry & accessories / Jewelry displays
Sleeping Dragon Ring Holder — crystal spire, 3 colours, no supports
A small dragon asleep in a coil around a crystal spire on a rock. Rings slide over the crystal and rest on the dragon's back. Three separate prints in three colours that drop together with no glue and no hardware, or one print-in-place 3-colour file for an AMS. 53 x 53 x 64 mm, about 46 g, no supports.
Toys & mechanisms / Fidgets
Flexi Snake — print-in-place articulated fidget that coils
A print-in-place snake that prints in one piece, no supports, and coils into a full spiral in your hand. 16 necked vertebrae on captive ball-and-stalk joints, each folding 50-70 degrees, plus a carved head with eyes and scale rings. Fully parametric: dial the number of segments and their length right in the .scad.
Jewelry & accessories / Earrings
Giraffe Earring — 2-Color AMS, Print-in-One, Both Facings
Full-body giraffe drop earring, 44 mm, sculpted with a flat back and a ring lug above the ossicones. Two coordinate-locked color solids in one STL: split to parts, assign cream and brown, print flat with no supports. Ships left-facing and right-facing so a pair can look the same way or at each other.
Jewelry & accessories / Brooches
Half-Amphora Brooch — a real amphora, full of flowers, cut in half
A magnetic brooch, 44 x 58 mm. Not an illusion and not a flat silhouette: a proper amphora is turned as a body of revolution, given two handles and a spray of flowers, and then cut in half on the plane of the brooch's back. What is left is 6 mm of true 3D relief with a flat back. The halving is also the print trick — a solid of revolution cut on its axis plane has zero overhang anywhere, so it prints face up with no supports. Two printed pieces, four colours, sealed magnets, no pin.
Jewelry & accessories / Brooches
Hollow-Face Vase Brooch — the vase is a hole, and it follows you
A magnetic brooch, 47 x 55 mm. The vase is not raised — it is the exact mould of a vase, sunk 5.2 mm into the plaque. Your eye refuses to read it as hollow, so it bulges out instead, and appears to turn and follow whoever walks past. Nothing moves; the viewer does. Two printed pieces, four colours in one 0.6 mm band, sealed magnets, no pin.
Toys & mechanisms / Mechanical
Wand Through the Wall — a Straight Wand Passes Through a Curved Slit
A dead-straight wand on a little turntable swings clean through two CURVED slits in a wall, twice per turn, without bending. The wand is skew to the axis, so it sweeps a hyperboloid; the wall cuts that in a hyperbola, and that is the slit. Four flat supportless parts, formula engraved on the base.
Toys & mechanisms / Mechanical
Jonah Whale - Press the Blowhole to Open the Jaw
A print-in-place whale toy. Press its blowhole and the jaw drops open to reveal a tiny diver.
Jewelry & accessories / Earrings
Möbius Hoop Earrings — Twisted Ribbon, Prints Flat, No Supports
A hoop that is a real Möbius band: a 6 mm ribbon swept round a 30 mm circle, three half-twists. No supports.
Toys & mechanisms / Whistles
Narwhistle — narwhal whistle, loud twin-chamber, one piece, no supports
A narwhal standing on its flukes on an ice floe that is also a loud pealess whistle: blow into the tusk, the sound leaves the blowhole. Two stopped-pipe chambers of unequal length pulse against each other — measured on the printed part at 2266 Hz with a ~66 Hz warble, the Fox-40 architecture. 102 x 40 x 31 mm, one piece, print-in-place, no supports, no hardware.
Jewelry & accessories / Earrings
Nudibranch Earring — 4-Color AMS Sea Slug, Print-in-One
Blue-and-orange aeolid sea slug charm, 36 mm, hanging head-up from a ring on its head. Four coordinate-locked colour solids in one STL: split to parts, assign white, blue, orange, brown, print flat with no supports.
Toys & mechanisms / Fidgets
Oldham Coupling Fidget — Offset-Shaft Constant-Velocity Demo Toy
A desk fidget that demos the Oldham coupling: spin the bottom knob and the top knob tracks it 1:1 even though the two shafts are parallel but laterally offset. A floating middle disc carries the rotation while its centre orbits a little circle. Five printed parts (4 unique designs), all flat and supportless. Useless, just fun.
Jewelry & accessories / Earrings
Panda Earring Charm — 2-Color AMS, Print-in-One
Seated giant-panda charm, 29.7 mm tall, sculpted with a flat back. Two coordinate-locked color solids in one STL: split to parts, assign white and black, print flat with no supports.
Boxes & storage / Catch-alls & coin banks
Piggy Bank 🐷 — top coin slot + finger-twist bottom plug
A classic chubby piggy bank: drop coins through the top slot (takes any circulating coin up to Ø33 mm), empty it by unscrewing the knurled bottom plug with your fingers — no tool. The pig prints as ONE belly-down body (snout, ears, curly tail, feet all integral) plus a separate twist plug. Watertight, no supports. Parametric OpenSCAD source included.
Jewelry & accessories / Earrings
Raven Skull Earring — flat silhouette dangle, mirrored pair, no supports
A raven (Corvus corax) skull in lateral profile as a flat dangle earring: a big domed braincase pierced by an Ø8 orbit, the heavy decurved corvid culmen with an open nare, and a mandible fused only at the articulation so an open jaw slot runs the length of the beak — that slot is what makes it read as a skull rather than a bird head. One flat piece, ~25 x 41 x 1.8 mm, 0.93 g, printed face-up with zero overhangs and no supports. Ships mirrored left and right STLs so a worn pair both faces outward, and a fully parametric OpenSCAD source: size, thickness, hang angle, orbit and nare, bail hole.
Decorations / Coasters
Nordic Rune Coasters — 12 motifs, carved rope lip, runic caddy
Ø90 mm Norse coasters with a twisted-rope lip, wood grain carved across the well and one of 12 motifs engraved in the middle — six Elder Futhark runes, six Norse icons. Each ships with an exact-fit inlay for two-colour AMS printing. Plus a stacking caddy whose wall carries a real runic inscription. No supports anywhere.
Decorations / Seasonal
Snowflake Set — Ornament · Coaster · Fridge Magnet · Earrings · Print-in-Place Cuff (Parametric)
A family of 6-fold dendrite snowflakes from one parametric generator: a tree ornament, an openwork drink coaster, a sealed-in fridge magnet, dainty earrings, a single cord charm, and a print-in-place hinged bracelet cuff that folds off the bed already articulated and locks with a toggle clasp. All print FLAT, face-down, NO supports.
Around the home / Small Tools
AC/DC Socket Plug — EU Child-Safety Blanker
Round disc that fills the recess of a EU Schuko/CEE 7/3 wall socket and blocks both phase holes. Two big spherical finger pockets on the dome let you pry it back out one-handed; a U-slot at one edge wraps around the earth pin so the plug seats flush in grounded sockets. Two-colour print: dark body + yellow lightning-bolt inlay on the dome (AC/DC theme). Ø 38 mm × 19 mm dome.
Jewelry & accessories / Earrings
Spider Drop Earring — the spider actually SWINGS on its dragline
An orb web with a spider hanging below it on a dragline that is a real pivot, not a printed line. The dragline's top end is an eye captured on a post at the web hub and closed by a cap, so the spider is a free pendulum that swings side to side as you move. Print-in-place: one flat plate, two bodies, no supports, nothing to assemble. 20.0 x 40.1 x 4.9 mm, ~0.6 g. Print two for a pair.
Decorations / Sculptures
Strigoi bust — Romanian folklore vampire, one part, no supports
A strigoi — the Romanian-folklore vampire — as a small shelf bust: gaunt skull, deep-set eyes under a heavy brow, hooked nose, ears swept back to points, jaw hanging open on two long canines, and a folk-embroidered collar of cross-stitch diamonds that is the Carpathian tell separating a strigoi from a generic Dracula. 70.7 x 42.0 x 49.0 mm, one part, one colour, prints flat on its plinth with no supports, no glue and no hardware.
Jewelry & accessories / Earrings
Tiny Book Earring — a wearable book that really opens, print-in-place hinge, no supports
A book small enough to wear that actually opens. One print-in-place piece: two covers on a seven-knuckle piano hinge with a captive pin, a hollow page cavity inside, and ONCE UPON engraved on the inner cover so the message only shows when you open it. 22 x 17.6 x 4.2 mm closed, 1.55 g, about 25 minutes, no supports and no hardware beyond an ear wire. Comes off the plate open flat; fold it once and it clicks shut on a printed detent bead, and a thumbnail in the fore-edge scallop pops it open again. Fully parametric OpenSCAD source — size, cover thickness, hinge clearance, detent grip and the engraved message are all variables.
Boxes & storage / Keepsake boxes / Nature
Toadstool 🍄 — twist-open bonbon capsule
A tiny Amanita-muscaria toadstool that twists open to hide a wrapped bonbon or candy inside. The red spotted cap is a screw-off roof; underneath is a clean toadstool stalk — Amanita skirt ring and a soft volva bulb at the base — with a hollow chamber. Two-colour AMS cap. Closed capsule is Ø46 × 52 mm (min sphere Ø58 mm) — fits inside a 2.7-inch (68.6 mm) capsule. No supports, parametric OpenSCAD source included.
Desk & office / Reading & writing
Trident Bookmark — Poseidon's Trident with a Page Stop (2-colour)
Poseidon's trident as a bookmark: the haft IS the page strip, and the 30 mm crossbar rests on the page block so it can never sink into the book. Prints flat at 1.2 mm, no supports. Single-colour or two-colour.
Around the home / Bowls
Twisted Vortex Bowl — one part, no supports
A catch-all bowl whose flutes spiral out of a small foot into a wide rim. The flutes climb at the same angle everywhere, so nothing on the outside of the bowl overhangs past 36 degrees and it prints with no supports and no brim. 46 mm foot, 78 mm rim, 45 mm tall, holds about 115 ml, around 30 g. Parametric OpenSCAD source included — twist, flare, flute pitch and depth are all named variables at the top.
Jewelry & accessories / Earrings
Viola Earring — 4-Color AMS Pansy Blossom, Print-in-One
Viola (pansy) blossom charm, 28 mm, hanging from a ring above the upper petals. Four coordinate-locked colour solids in one STL: split to parts, assign magenta, violet, yellow, dark, print flat with no supports.
Decorations / Magnets
Weather Dial Fridge Magnet — spin it to today's weather
A fridge magnet with a live front. Thumb the knurled rim through the side notch and the dial clicks into four detented positions — sun, rain, cloud, snow — showing one icon at a time through the porthole. The three magnets are sealed inside solid plastic on both faces: no glue, no exposed metal against the door, nothing to fall out. They go in during the print, at a single pause. The dial ships as five files sharing one coordinate frame, so it prints in five colours with nothing to group by hand. Prints supportless. Parametric OpenSCAD source included.
Jewelry & accessories / Earrings
Winged Sandal Earrings — Hermes' talaria, flat two-colour pair
The winged sandal of Hermes (talaria, the 'Mercury foot') as a flat two-colour dangle earring — sole, up-curled toe and an ankle strap that arcs up and becomes the bail, with a feathered heel wing in a second colour. Both colours tile ONE flat plate at the same height, so they print flush in the same layers with no step, no overlap and no supports. ~35 mm tall, 2.2 mm thick, about 2 g for the pair. Mirrored L+R so the toes point outward when worn.
Decorations / Seasonal
Wizard Lantern — stained-glass LED tealight lantern with six slide-in panes
Hexagonal gothic lantern for an LED tealight: six translucent stained-glass panes slide into channels behind the windows (moon, star, potion, wizard hat, crystal, toadstool), a pointed roof clips on with two release tabs and hangs by its cord eye. 8 prints, no supports, no glue.
Jewelry & accessories / Sewing buttons
Yggdrasil Buttons — Norse world-tree sewing buttons, 15 / 20 / 25 mm, shank or 2-hole
Real, wearable sewing buttons with the Norse world-tree on the face. Five sizes/styles: Ø15, 20, 25 mm with a hidden thread tunnel in the underside (the face stays whole — no holes bored through the tree), plus classic 2-hole versions at Ø15 and 20. Each ships a named-solid 2-colour companion for AMS. Prints flat, face up, no supports, no brim. Fully parametric: any diameter renders with the motif's stroke widths automatically held at or above one nozzle width.
Jewelry & accessories / Earrings
Zebra Earring — 2-Color AMS, Print-in-One, Both Facings
Full-body zebra drop earring, 32 mm, sculpted with a flat back and a ring lug on the crest. Two coordinate-locked color solids in one STL: split to parts, assign white and black, print flat with no supports. Ships left-facing and right-facing so a pair can look the same way or at each other.
Desk & office / Organizers / Pen Holders
Amphora Pen Pot — Panathenaic Prize Amphora, Engraved Bands, No Supports
A Greek amphora as a desk pen pot: running-athlete frieze, Greek-key meander, ray and palmette bands, all engraved 0.7 mm into the curved wall. One part, prints upright with no supports. The foot is deliberately widened over the museum original so it does not tip when a pen leans.
Desk & office / Electronics / Cables
Desk Cable Rack — Pegs or Pole Variant (Parametric)
A simple desk-side cable rack to keep charging cables, headphones, and props off the floor. Two variants share the same base + back wall: a 6-peg version (each cable hooks over its own peg) and a single-pole version (cables drape over a full-length pole with a back-stop shelf). 200 × 150 × 100 mm. Prints flat on its back, no supports.
Desk & office / Organizers / Paper Notes
Classroom Desk Name Plate — slide-in letter tiles, one alphabet sheet spells the whole class
A school desk name plate whose name is not baked into the STL. One dovetail track, one tile per letter, threaded in from the open end. Print one alphabet sheet for the whole class and one plate per desk — re-spell it when the seating plan changes instead of re-slicing a custom model for every child. 41 tiles (A-Z plus Czech accented capitals), blanks that centre the name, an end stop that locks the row, and a pair of brackets that stand the plate up as a tent. Every letter also ships as its own file, plain and two-colour. No hardware, no glue, no supports.
Desk & office / Organizers / Pen Holders
Hedgehog Pen & Pencil Holder — your pens become the quills
A bald little hedgehog whose quills are YOUR pens and pencils. The smooth dome body has an angled fan of 11 blind bores drilled into its back; plug pens and pencils in and they radiate outward exactly like real quills. Dimple eyes and a snout finish the face. Prints belly-flat on the bed with zero supports — the dome is the top half of an ellipsoid so every wall leans inward going up. Single part, single colour, just print and load it up.
Desk & office / Electronics / Stands
Keyboard Riser — Split, Dovetail-Joined, Parametric (60 / 100 / 180 mm Lift)
Open-frame stand that lifts a keyboard off the desk, leaving the space underneath clear. Three ready-to-print configurations: 60 and 100 mm lift for a 440 × 135 mm board, and 180 mm for a 313 × 123 mm 75 % board (Keychron K2 size). A 3 mm rim keeps the board from sliding off; a honeycomb deck spreads its weight. Too long for a 256 mm bed, so it splits into two halves that re-join with a drop-in dovetail key — no glue, no tools. Fully parametric: change one variable for any other board or height.
Desk & office / Reading & writing
Filigree Letter Opener — Flat Leaf Blade, No Supports
A 210 mm single-piece letter opener with a leaf-shaped chisel-ground blade and an ornamental filigree handle (quatrefoil rosette, flanking ovals, hang hole). Prints flat, no supports. PETG recommended for a stiff, durable blade.
Desk & office / Organizers / Modular
MagDock — Magnetic Desk & Shop Organizer Family
A family of small organizers that embed neodymium discs in their backs, so they snap onto ANY ferrous surface — printer frame, fridge, toolbox, filing cabinet, radiator. Hook, tray, tall caddy, pliers/scissors slots, and a bare puck. The magnets are sealed inside DURING printing (mid-print pause), so no caps and no glue. Every part prints flat on its back with NO supports.
Desk & office / Electronics / Stands
Monstera Phone Stand — cable-ready desk holder
A one-piece leaf phone stand with open charging access, corner ledges, and an 11 mm slot for slim cases.
Desk & office / Electronics / Cables
Pretzel Cable Clip — Two-Colour Desk Cable Holder
A 58 x 44 mm pretzel-shaped desk clip for one small charging cable, with white salt accents. Flat print, no supports.
Desk & office / Organizers / Pen Holders
Twisted Ribbed Pen Cup — one part, no supports
A rounded-square desk cup whose whole surface is fine ribs turning through 90 degrees from the base to the rim. The cavity twists at the same rate as the shell, so the wall stays 1.6 mm the whole way up and nothing inside collects dust in a corner. 50 x 50 x 70 mm, 63 mm across the twisted corners, about 40 g, one part, no supports, no glue. Parametric OpenSCAD source included — twist angle, rib pitch, rib depth, corner radius and height are all named variables at the top.
Desk & office / Electronics / Cables
USB Drive Caddy — Hex-Grill Open-Front Cubby
N×M open-front cubby for low-profile USB-C 'disc' drives. Drives lay flat and slide in from the front; ~4 mm sticks out for pinch removal. Decorative hex perforation on top + sides. Ships pre-rotated — open face prints UP, back wall on the bed, zero supports.
Around the home / Hooks
Cap Magnet Hook
A little magnetic hook shaped like a baseball cap — the curved brim is the hook. Two Ø10x5 mm neodymium discs sit sealed inside the flat back and stick it to any steel surface (fridge, locker, radiator, steel door frame). No screws, no supports. A screw-mount version is included too. Holds LIGHT things only.
Around the home / Hooks
Bag Hook for a Desk Edge or a Chair Back
Clamps onto a table edge, a desk lip or a chair backrest and gets the backpack off the floor. One part, no supports, no screws, no glue. Three sizes included — 20, 25 and 30 mm jaws — and a sprung tongue inside each takes up the slack below that, so between them they cover roughly 10 to 30 mm. A 7-minute fit-test coupon is included for every size so you can check the grip on your own table before printing the whole thing. The source file is included and fully parametric: change one number and you get a jaw for any thickness.
Kitchen / Tableware
Norse Drinking Horn Shot Glasses — 4 Horns + Runed Flight Tray
Four Norse drinking-horn shot glasses, 40 ml each, plus a runed flight tray. Display piece: the tray tips if moved.
Kitchen / Tableware
Kiwi Bird Tea Bag Holder — feathered, beak holds the string, no supports
A sitting kiwi whose back is a bowl for the used tea bag; the long beak probes the table so you wrap the string round it and the tag stays dry. Shaggy feather relief on the body. One part, 46 x 79 x 27 mm, prints belly-down with no supports.
Kitchen / Tools
Lemon / Citrus Hand Squeezer — Reamer + Strainer Cap + Pour Spout
Two-piece manual citrus juicer: a strainer cap with a swirly helical reamer cone sits on a 95 mm bowl with an integrated U-trough pour spout. Twist a lemon-half over the cone, juice runs through the strainer holes into the bowl, lift the cap off and pour. Prints in two parts, no supports, no bridges.
Kitchen / Tableware
Wave-Crest Napkin Ring — sculpted, no supports
A napkin ring whose top rim rises and falls in three slow waves, with the wall swelling thickest directly under each crest so the band resolves into three lobes with a waist between them. The bore stays a true cylinder, so a rolled cloth napkin always passes. Every curved surface faces up or outward and the bottom rim is flat on the bed, which means zero overhang by construction: it prints standing, exactly as modelled, with no supports and no brim.
Kitchen / Tableware
Napkin Tray — Toblerone-Style Holder w/ Diamond Cross-Hatch
Upright napkin holder shaped like a Toblerone bar: flat rounded base + two isosceles-triangular side walls leaning in at the peak. Folded paper napkins (~8×16 cm) stack between the walls. Diamond cross-hatch engraved on every visible face — top of the base + both outer faces of each wall. Prints flat on bed, single piece, no supports.
Kitchen / Sink Organizers
Sink-Rim Sponge Tray — Hooks Over the Rim, Drains Into the Basin
Single-bay sponge tray that hooks over a kitchen sink rim and hangs inside the basin. Sized to a standard kitchen sponge (~95×60×25 mm) with ~5 mm slack on every side. Floor drain slots + lower-wall drains let water run straight back into the sink — sponge dries instead of sitting in a puddle. Prints in one piece, open-top up, no supports.
Kitchen / Tools
Utensil Rest — spoon / ladle / spatula rest with a deep drip bowl, anti-soak ribs and a raised handle saddle
A hob-side spoon rest that keeps the handle off the counter. The spoon head sits in a 8.5 mm-deep elliptical drip bowl, radial ribs hold it up out of its own drips, and a 30 mm saddle at the end cradles the handle in a U-groove. One piece, 132 x 88 x 30 mm, prints flat with no supports. Fully parametric OpenSCAD source included.