TAGGED
Storage
26 designs tagged “Storage”.
Bathroom / Makeup organizers
Apothecary Brush Drying Rack — hangs brushes bristles-down
A rack that dries makeup brushes the way every brush-care guide says to dry them: hanging HEAD DOWN over a drip tray. A brush stood bristles-up runs water into the ferrule, the glue softens and the brush sheds — this is the one makeup problem with a real failure mode behind it, and nothing prints a rack that fixes it. The grip is a WEDGE SLOT, not a hole: handles run about 6–12 mm and no single bore fits them, so each of the six slots tapers 13 → 5 mm over 22 mm and every brush catches at its own diameter, at about 9.4° per side, well inside PLA's friction angle. 172 mm of measured hang clears a 190 mm brush. The rail lifts straight off the two posts to load, and the tray is then a plain open dish you tip and rinse. 2 parts, 176 × 78 × 219 mm, 301 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Cauldron Makeup Organizer — a bowl with no corners, no supports
A three-legged cauldron that sorts makeup, and the bowl is the whole idea: it is a truncated sphere, so there is no corner anywhere inside it for powder to pack into. A 2.6 mm wall runs into a 3 mm floor through a 4 mm fillet rather than a crease, and one wipe reaches every part of the inside. Brushes stand in it bristles-up and fan out against the curve; a 4-way cross drops in to quarter the bowl for jars, sponges, compacts and hair ties, and lifts out to leave a plain brush cup. The three legs are a separate trivet ring the bowl drops into on a 45 degree cone, because legs cast under the bowl print as a horizontal overhang between them. 3 parts, 92 x 90 x 77 mm assembled, 117 g, no supports, no hardware, no glue — assembly is dropping one part into another.
Bathroom / Makeup organizers
Dragon Wing Palette Rack — eyeshadow palettes on edge, no supports
An eyeshadow-palette rack whose fins are the finger bones of a dragon wing. Palettes stand on edge like books, so you read the spines and pull one out one-handed instead of excavating a stack. Five 16.5 mm slots take anything up to an 18 mm palette, with 100 mm of clear depth between the front rail and the back spine and a 76 mm shortest fin. Every segment of the fin profile is upward-facing, so a 112 mm tall part prints with ZERO supports. 1 part, 118 x 128 x 112 mm, no supports, no hardware, no assembly.
Bathroom / Makeup organizers
Frost Crystal Casket — makeup organizer, no supports
A block of glacier ice with a quartz cluster growing out of the back, and the cluster is the working part: all seven crystals are bored straight through, so a brush pushed into a shard stands bristles-up while its handle hangs in the box below — which is why a 120 mm and a 220 mm brush end up standing at the same height. Bores are cut to measured stock: Ø27 for mascara, two Ø23 that neck down to Ø14 so a lipstick rests on the shoulder, and four brush bores at Ø16 and Ø11. There is not one blind hole in the model and the well underneath is a single cavity with a 4 mm cove where the floor meets the wall, so nothing has a square corner to pack powder into. 3 parts, 132 × 114 × 100 mm, 298 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Great Helm Makeup Organizer — knight's helm, no supports
A 13th-century flat-topped great helm that is a makeup organizer on the inside. The crown is open and a lift-out liner drops onto the rim carrying the whole bore field, so brushes stand out of the helm like a crest: six brush bores go straight THROUGH so the handle hangs in the cavity and a 120 mm and a 220 mm brush stand at the same height, three tube bores (Ø27 mascara, two Ø23 lipstick) neck down instead of bottoming out, and an 88 × 24 mm palette slot rests a compact on an open 8 mm ledge. Not one bore is blind, so powder falls through into a smooth drum you tip out and rinse. 2 parts, 134 × 125 × 150 mm, 307 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Medieval Well Makeup Organizer — no supports
A stone draw-well with a winding gantry, a gable roof and a bucket on a string — and a makeup organizer inside it. The coping stone is a lift-off plate carrying all 11 bores, and not one of them is blind: a brush handle hangs free down the shaft, a mascara rests in a 45° seat cone instead of bottoming out, and loose powder falls straight past into a rinse dish in the plinth. Cleaning is lift, lift, tip, rinse. 5 parts, Ø144 × 176 mm, 420 g, no supports, no hardware, no glue — just ~120 mm of twine for the bucket.
Bathroom / Makeup organizers
Moonwake Makeup Wardrobe — a 240 mm two-door cabinet with printed hinges and lift-off door bins
A 240 x 200 x 228 mm cabinet for makeup and hygiene: two engraved doors on four printed pins that swing to 160 degrees, four lift-off bins on the door panels, and two removable organizers inside for brushes, tubes and palettes. 13 parts, no hardware, no glue, no supports.
Board games / Classic games / Dominoes
Domino Box — Sleeve + Tray for the Double-Six 28-Tile Set (OpenSCAD)
Two-piece storage for a full 28-tile double-six domino set. Outer sleeve (closed on 5 faces, open on one short end) + inner tray with a Ø28 mm semicircular thumb-notch on its front wall. Tiles lie flat in a 4×2 grid of 4-tile stacks (32-slot capacity). Sleeve prints with the open mouth UP — fully supportless. Engraved decorative pip pattern on every long face. Parametric SCAD lets you re-tune tile dimensions, slop, layout (piles_x × piles_y), pip pattern, or wall thicknesses.
Boxes & storage / Keepsake boxes / Fantasy
Library of Alexandria box — a magnetic box under the great dome
The Library of Alexandria as a box: a white-marble hall behind an arcade of pointed arches, a full-width stair, four turrets under gilded onion domes and a great ribbed dome on a chevroned drum. Everything above the cornice is the lid, and eight Ø5 × 3 mm magnets buried mid-print hold it shut. 118 × 96 × 113 mm outside, 90 × 60 × 45 mm inside. Six STLs, two prints, no supports, no glue.
Boxes & storage / Organizers / Baskets
Honeycomb Hinged Storage Box — Large (PIP, 3 sizes)
Big rectangular storage box with hex pattern on every wall + print-in-place piano hinge — prints OPEN, snaps shut, no assembly. Three sizes bundled.
Boxes & storage / Keepsake boxes / Nature
Capybara Lock Box — Magnetic Two-Key Drawer Box
A drawer box that only opens when you set TWO capybara figurines on its lid pads. The capybaras are the keys — each hides a magnet that lifts a hidden loose-magnet shear pin off the drawer rail. Both keys at once = a two-capybara combination lock. Multi-color engraved lid, captive drawer, self-locking. Uses hobby disc magnets you drop in during printing. Keys included.
Boxes & storage / Organizers / Drawers
Carousel Drawer Tower — Stacking Swing-Out Parts Organiser
A modular desk organiser of pie-wedge bins that swing out around a central post. Stack as many tiers as you like; a wide fillable ballast dish keeps it planted. Fully parametric OpenSCAD.
Boxes & storage / Keepsake boxes / Fantasy
Castle keep box — a fortified keep that opens at the wall-walk
A 112 mm square castle keep whose lid is the wall-walk: lift the battlements, four corner drums and their tiled conical roofs straight off and the keep is a 70 x 70 x 64 mm box. Two prints, no supports, no hardware, nothing to glue. The lid rests rather than latches, so it is a table box, not a travelling one. Multi-colour for the AMS, and it still reads as a castle in one filament.
Boxes & storage / Keepsake boxes / Geometric
Crumpled Paper Box — Magnetic Lid
Small crumpled-paper storage box with an enclosed magnetic lid. Two prints, eight 5 x 3 mm magnets.
Boxes & storage / Keepsake boxes / Fantasy
Elven seed archive — four-colour drawer box, pinned roof, no glue
Four-colour elven drawer box, 240 x 200 x 70 mm closed, with a scalloped leaf roof, arched tracery windows and a full-width pull-out drawer. Three prints plus four friction pins, no glue, no supports, no hardware.
Boxes & storage / Keepsake boxes / Fantasy
Haunted Castle Magnetic Storage Box
Halloween castle storage box with a lift-off roof, hidden magnets and two printing routes: multicolour or separate parts.
Boxes & storage / Organizers / Tools & small parts
Haunted House Screw Organizer — 3 Drawer Floors, Crooked Mansard Roof
A crooked Victorian mansard house whose three floors are pull-out drawers for screws, nuts and bits. Five parts, no hardware, no glue, no supports; the pumpkin face and glowing windows are a second colour on the drawer fronts.
Boxes & storage / Keepsake boxes / Geometric
Letohrádek Hvězda — star-shaped building box
Prague’s star-shaped palace as a storage box with a loose roof cover. Not suitable for travel packaging.
Boxes & storage / Organizers / Baskets
Parametric Stackable Storage Box (1×1 to 5×5)
Stackable storage drawers with stud-and-hole interlock — they tile sideways and stack vertically with each other. 25 ready-to-print sizes from 1×1 up to 5×5, with both door orientations for every rectangle, plus 2 height/fit specials. Parametric SCAD source included — change pitch, height, or footprint to derive any size you want (the SCAD goes well past 5×5).
Boxes & storage / Keepsake boxes / Fantasy
Mead hall box — a Viking longhouse whose whole roof lifts off
A 199 mm Viking longhouse whose whole shingled roof lifts off, leaving a 177 x 83 x 31 mm box with the hollow roof above it. Two prints in one wood-fill filament, no supports, no hardware, nothing to glue. Every plank, knot and shingle is cut and jittered from one seed, so it reads hand-built. The roof rests on a tongue, it does not latch, so it is a table box, not a travelling one.
Boxes & storage / Keepsake boxes / Fantasy
Pirate treasure chest — print-in-place hinged trinket box, two colour
A 100 mm barrel-top pirate chest that comes off the bed as one working unit. The piano hinge prints in place, so there is no assembly, no pin to fit and no glue. Two-colour for the AMS: wood planks plus iron straps, banding, corner brackets, lock plate and hasp.
Boxes & storage / Keepsake boxes / Fantasy
Renaissance castle box — inspired by Rosenborg, the whole castle lifts off a hidden tray
A 240 x 108 x 250 mm Dutch Renaissance castle, inspired by Rosenborg in Copenhagen but not a 1:1 replica, that is a box: the whole four-colour castle is one print and lifts off a hidden tray. Almost three days of printing with a four-slot automatic filament changer. No supports, no hardware, no glue.
Boxes & storage / Organizers / Baskets
Stackable Lattice Basket — 4 Sizes + Parametric SCAD
Cross-stackable lattice baskets with cone-peg corner posts — any basket stacks onto any other basket. Four ready-to-print sizes from 5×5×5 cm cube up to a 20×12×8 cm tray, plus an optional cone-foot leg accessory. One open short side per basket so you can reach contents while the stack stays put. Parametric SCAD included — override basket_l/basket_w/body_h to derive any size; corner-post + peg geometry is shared so derived sizes still cross-stack with the printed ones.
Boxes & storage / Organizers / Baskets
Truchet Bucket Box — 5-Compartment Organizer with Maze-Pattern Walls
A lidless 5-bucket organizer with a flowing Truchet-tile maze pattern engraved on all four walls. Great for beads, hardware, ball bearings, craft bits. No supports, prints flat. Fully parametric OpenSCAD source included — change bucket count, size, or pattern.
Boxes & storage / Keepsake boxes / Geometric
Bayonet Tube — Ø50 × 60 mm with Quarter-Turn Locking Caps
Cylindrical tube container with two IDENTICAL bayonet caps. Drop a cap on either end, push, twist 35°, locked. No hardware, no supports. Parametric OpenSCAD source included.
Boxes & storage / Keepsake boxes / Fantasy
Tudor house box — half-timbered town house whose upper storey lifts off
A 184 x 214 x 150 mm half-timbered Tudor town house that is a box: the jettied upper storey, twin-gabled tile roof and chimney lift off as one lid over a 164 x 194 x 90 mm cavity. Two prints, nine coordinate-locked colour solids, no supports, no hardware.