TAGGED
Gothic
17 designs tagged “Gothic”.
Bathroom / Makeup organizers
Apothecary Brush Drying Rack — hangs brushes bristles-down
A rack that dries makeup brushes the way every brush-care guide says to dry them: hanging HEAD DOWN over a drip tray. A brush stood bristles-up runs water into the ferrule, the glue softens and the brush sheds — this is the one makeup problem with a real failure mode behind it, and nothing prints a rack that fixes it. The grip is a WEDGE SLOT, not a hole: handles run about 6–12 mm and no single bore fits them, so each of the six slots tapers 13 → 5 mm over 22 mm and every brush catches at its own diameter, at about 9.4° per side, well inside PLA's friction angle. 172 mm of measured hang clears a 190 mm brush. The rail lifts straight off the two posts to load, and the tray is then a plain open dish you tip and rinse. 2 parts, 176 × 78 × 219 mm, 301 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Dragon Wing Palette Rack — eyeshadow palettes on edge, no supports
An eyeshadow-palette rack whose fins are the finger bones of a dragon wing. Palettes stand on edge like books, so you read the spines and pull one out one-handed instead of excavating a stack. Five 16.5 mm slots take anything up to an 18 mm palette, with 100 mm of clear depth between the front rail and the back spine and a 76 mm shortest fin. Every segment of the fin profile is upward-facing, so a 112 mm tall part prints with ZERO supports. 1 part, 118 x 128 x 112 mm, no supports, no hardware, no assembly.
Boxes & storage / Keepsake boxes / Fantasy
Coffin Pencil Case — Magnetic Box with a Death's-Head Moth Lid
A toe-pincher coffin box for pens, markers and brushes. The lid is held by six pairs of hidden magnets buried mid-print, so no fastener is visible anywhere. Prints flat, no supports, one colour or two.
Around the home / Hooks
Bat Ceiling Hook — hangs by its own feet, head down, like a real bat
A roosting bat that hooks over a ceiling hook by its two toe-rings and gives you two open claw hooks at the bottom for cords, string lights or a planter. One part, no supports, no assembly.
Decorations / Sculptures
Drowned Watchman — barnacle skull, four-colour anatomical decoration
Anatomical skull that looks pulled from the seabed: a broken temple, shallow cracks, six barnacles and patches of olive growth. One 89 × 128 × 94 mm print in four PLA colours, or one colour and paint. Fixed jaw, tree supports, no assembly. Anatomy by Dr Mariano Coretti, CC BY-SA 4.0.
Around the home / Hooks
Gargoyle Wall Hook
Gothic gargoyle head on a round backplate — wall-mounted hook for towels, rags, keys, charms. Protruding face acts as the hook; drape items over it. Two screw holes for drywall mount.
Jewelry & accessories / Earrings
Melting Candle Earring — 2-Color Charm
Parametric dripping wax candle earring charm — a tapered candle body with a melted pool rim, six irregular wax drips ending in bulbous drops, a teardrop flame and an integral hanging loop. Two-color for AMS: ivory wax body + orange flame as two named solids for Split-to-Parts. Prints STANDING, flame up, support-free (wide base on the bed, everything narrows upward). Print twice for a pair.
Jewelry & accessories / Earrings
Phoenix Earring Charm — perched firebird (mirrored pair)
A majestic perched phoenix charm for earrings or pendants, about 32 mm tall, with a jump-ring bail baked into the nape so it hangs upright. Ships as a mirrored left/right pair so both birds face outward. Styled after a Fawkes-like firebird — a swept-back crest, swan-curved neck, folded wings and a long fanned tail that becomes the dangle.
Jewelry & accessories / Earrings
Raven Skull Earring — flat silhouette dangle, mirrored pair, no supports
A raven (Corvus corax) skull in lateral profile as a flat dangle earring: a big domed braincase pierced by an Ø8 orbit, the heavy decurved corvid culmen with an open nare, and a mandible fused only at the articulation so an open jaw slot runs the length of the beak — that slot is what makes it read as a skull rather than a bird head. One flat piece, ~25 x 41 x 1.8 mm, 0.93 g, printed face-up with zero overhangs and no supports. Ships mirrored left and right STLs so a worn pair both faces outward, and a fully parametric OpenSCAD source: size, thickness, hang angle, orbit and nare, bail hole.
Jewelry & accessories / Earrings
Spider Drop Earring — the spider actually SWINGS on its dragline
An orb web with a spider hanging below it on a dragline that is a real pivot, not a printed line. The dragline's top end is an eye captured on a post at the web hub and closed by a cap, so the spider is a free pendulum that swings side to side as you move. Print-in-place: one flat plate, two bodies, no supports, nothing to assemble. 20.0 x 40.1 x 4.9 mm, ~0.6 g. Print two for a pair.
Decorations / Sculptures
Strigoi bust — Romanian folklore vampire, one part, no supports
A strigoi — the Romanian-folklore vampire — as a small shelf bust: gaunt skull, deep-set eyes under a heavy brow, hooked nose, ears swept back to points, jaw hanging open on two long canines, and a folk-embroidered collar of cross-stitch diamonds that is the Carpathian tell separating a strigoi from a generic Dracula. 70.7 x 42.0 x 49.0 mm, one part, one colour, prints flat on its plinth with no supports, no glue and no hardware.
Jewelry & accessories / Earrings
Strix Owl Earring Charm
A finely detailed horned-owl charm for earrings or pendants, about 25 mm tall with a jump-ring bail baked into the crown. Note: the photographed pair was printed in wood-fill PLA, which is NOT recommended for a piece this small and detailed — plain or silk PLA gives far cleaner results.
Jewelry & accessories / Earrings
Gothic Pigtail Girl Silhouette Earring — Flat Charm
A flat full-body silhouette of a somber girl in braided pigtails and a dark dress, sized as a dangle earring charm with an integral bail loop at the crown. Prints FLAT on its back, face up — zero overhangs, no supports. About 42 mm tall. Print twice for a pair.
Decorations / Seasonal
Wizard Lantern — stained-glass LED tealight lantern with six slide-in panes
Hexagonal gothic lantern for an LED tealight: six translucent stained-glass panes slide into channels behind the windows (moon, star, potion, wizard hat, crystal, toadstool), a pointed roof clips on with two release tabs and hangs by its cord eye. 8 prints, no supports, no glue.
Kitchen / Drink Holders
Bone Tankard — skeleton cup holder with femur staves & skull
A barrel-stave tankard built from bones: 24 randomized cartoon femurs as staves, a relief skull fused into the front, and a bone-chain handle. Drop in a glass or 330 ml can. Prints upright with NO supports. Fully parametric OpenSCAD.
Decorations / Sculptures
Gothic Stone Throne — decorative sculpture
A miniature gothic stone throne: a spired skull-and-scroll backrest, sweeping wave/dragon-wing armrests, and a stepped rune plinth. ~143 × 146 × 211 mm — a chunky display sculpture for a desk, shelf, or D&D table. Prints as one solid watertight body.
Desk & office / Organizers / Pen Holders
Sunflower Pen Cup — Petal Crown + Gothic Quatrefoil Body
Tall pen / marker cup with an 18-petal sunflower crown at the rim and a brick-grid of gothic quatrefoils (cathedral-rose pattern) engraved into the body wall. Single open chamber, prints upright without supports.