TAGGED
Organizer
43 designs tagged “Organizer”.
Bathroom / Makeup organizers
Apothecary Brush Drying Rack — hangs brushes bristles-down
A rack that dries makeup brushes the way every brush-care guide says to dry them: hanging HEAD DOWN over a drip tray. A brush stood bristles-up runs water into the ferrule, the glue softens and the brush sheds — this is the one makeup problem with a real failure mode behind it, and nothing prints a rack that fixes it. The grip is a WEDGE SLOT, not a hole: handles run about 6–12 mm and no single bore fits them, so each of the six slots tapers 13 → 5 mm over 22 mm and every brush catches at its own diameter, at about 9.4° per side, well inside PLA's friction angle. 172 mm of measured hang clears a 190 mm brush. The rail lifts straight off the two posts to load, and the tray is then a plain open dish you tip and rinse. 2 parts, 176 × 78 × 219 mm, 301 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Cauldron Makeup Organizer — a bowl with no corners, no supports
A three-legged cauldron that sorts makeup, and the bowl is the whole idea: it is a truncated sphere, so there is no corner anywhere inside it for powder to pack into. A 2.6 mm wall runs into a 3 mm floor through a 4 mm fillet rather than a crease, and one wipe reaches every part of the inside. Brushes stand in it bristles-up and fan out against the curve; a 4-way cross drops in to quarter the bowl for jars, sponges, compacts and hair ties, and lifts out to leave a plain brush cup. The three legs are a separate trivet ring the bowl drops into on a 45 degree cone, because legs cast under the bowl print as a horizontal overhang between them. 3 parts, 92 x 90 x 77 mm assembled, 117 g, no supports, no hardware, no glue — assembly is dropping one part into another.
Bathroom / Makeup organizers
Dragon Wing Palette Rack — eyeshadow palettes on edge, no supports
An eyeshadow-palette rack whose fins are the finger bones of a dragon wing. Palettes stand on edge like books, so you read the spines and pull one out one-handed instead of excavating a stack. Five 16.5 mm slots take anything up to an 18 mm palette, with 100 mm of clear depth between the front rail and the back spine and a 76 mm shortest fin. Every segment of the fin profile is upward-facing, so a 112 mm tall part prints with ZERO supports. 1 part, 118 x 128 x 112 mm, no supports, no hardware, no assembly.
Bathroom / Makeup organizers
Frost Crystal Casket — makeup organizer, no supports
A block of glacier ice with a quartz cluster growing out of the back, and the cluster is the working part: all seven crystals are bored straight through, so a brush pushed into a shard stands bristles-up while its handle hangs in the box below — which is why a 120 mm and a 220 mm brush end up standing at the same height. Bores are cut to measured stock: Ø27 for mascara, two Ø23 that neck down to Ø14 so a lipstick rests on the shoulder, and four brush bores at Ø16 and Ø11. There is not one blind hole in the model and the well underneath is a single cavity with a 4 mm cove where the floor meets the wall, so nothing has a square corner to pack powder into. 3 parts, 132 × 114 × 100 mm, 298 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Great Helm Makeup Organizer — knight's helm, no supports
A 13th-century flat-topped great helm that is a makeup organizer on the inside. The crown is open and a lift-out liner drops onto the rim carrying the whole bore field, so brushes stand out of the helm like a crest: six brush bores go straight THROUGH so the handle hangs in the cavity and a 120 mm and a 220 mm brush stand at the same height, three tube bores (Ø27 mascara, two Ø23 lipstick) neck down instead of bottoming out, and an 88 × 24 mm palette slot rests a compact on an open 8 mm ledge. Not one bore is blind, so powder falls through into a smooth drum you tip out and rinse. 2 parts, 134 × 125 × 150 mm, 307 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Medieval Well Makeup Organizer — no supports
A stone draw-well with a winding gantry, a gable roof and a bucket on a string — and a makeup organizer inside it. The coping stone is a lift-off plate carrying all 11 bores, and not one of them is blind: a brush handle hangs free down the shaft, a mascara rests in a 45° seat cone instead of bottoming out, and loose powder falls straight past into a rinse dish in the plinth. Cleaning is lift, lift, tip, rinse. 5 parts, Ø144 × 176 mm, 420 g, no supports, no hardware, no glue — just ~120 mm of twine for the bucket.
Bathroom / Makeup organizers
Moonwake Makeup Wardrobe — a 240 mm two-door cabinet with printed hinges and lift-off door bins
A 240 x 200 x 228 mm cabinet for makeup and hygiene: two engraved doors on four printed pins that swing to 160 degrees, four lift-off bins on the door panels, and two removable organizers inside for brushes, tubes and palettes. 13 parts, no hardware, no glue, no supports.
Bathroom / Washing & personal care
Q-tip Cup — Fluted Cylinder with Snap-Fit Lid
Ø69 × 60 mm fluted cup that holds ~250 standard cotton swabs, with a faceted gem-top lid that snaps on with an audible click. Doric-style vertical flutes (24 concave grooves) on the cup, octagonal gem dome on the lid. Two STLs, prints flat, no supports.
Bathroom / Makeup organizers
Tenshu Makeup Organizer — Japanese castle keep, 3 lift-off storeys
A Japanese castle keep (tenshu) that sorts makeup. Every roof is the lid of the storey under it: the base holds four compacts on edge in a lift-out comb plus a polish bay, the second storey has three coved lanes for a mascara, lipsticks and pencils lying down, the third a tweezer lane and two cells for lashes, pins and rings. Every pocket is a hull of four spheres, so the floor meets the wall on a 4 mm cove and nothing is a square corner or a blind hole: lift, lift, lift, tip, rinse. Five parts, no supports, no glue, no hardware — each lid seats on a 2.4 mm ring so the stack does not rock, and magnets are an option, not a need. Ships as one-colour STLs and, for a multi-filament printer, as one three-colour STL per part that Split to Parts divides into exactly three: cream plaster, dark timber, slate stone-and-tile. A five-colour split-to-parts STL per part ships too, if you have the slots for a separate plinth grey and gold shachihoko.
Bathroom / Makeup organizers
Wizard Tower Makeup Organizer — 4 lift-apart tiers
A wizard's tower that sorts makeup. Brushes hang bristles-up from five wedge bores through the roof cone, so each one catches at its own handle diameter and a 120 mm and a 190 mm brush stand at the same height. The balcony deck takes a mascara, two lipsticks and three pencils; the plinth is a deep open bin for polish and jars. Every one of the eleven openings is a THROUGH hole and the bin floor is coved into the wall, so powder falls through instead of packing into a blind corner: the tower lifts apart into four pieces you tip and rinse under a tap. No supports, no glue, no hardware — every joint is a triangular tongue that drops into a V-groove.
Board games / Find your game / Cascadia
Cascadia Market Rack + 3D Wildlife Tokens
A two-in-one Cascadia upgrade: a market-row display rack that holds the four face-up habitat tile + wildlife token pairs on a gentle 15° slope, PLUS a full set of five sculpted 3D wildlife tokens (bear, elk, salmon, hawk, fox) that replace the flat wooden discs and drop straight into the rack's Ø19 cups. The rack prints flat and supportless in one part; each animal prints upright on a Ø18 base disc in its own colour — no AMS, no paint. Parametric OpenSCAD source included.
Boxes & storage / Organizers / Baskets
Honeycomb Hinged Storage Box — Large (PIP, 3 sizes)
Big rectangular storage box with hex pattern on every wall + print-in-place piano hinge — prints OPEN, snaps shut, no assembly. Three sizes bundled.
Boxes & storage / Organizers / Tools & small parts
Coin Cell Battery Dispenser — multi-section tray (parametric OpenSCAD)
Half-cylinder edge-mount wells for coin cells: pinch one out by the visible half. Six sections cover CR2032 / CR2025 / CR2016 / CR1620 / LR1130 / LR44 — 29 cells total. Parametric: edit the sections list to retarget any cell stash.
Boxes & storage / Organizers / Drawers
Carousel Drawer Tower — Stacking Swing-Out Parts Organiser
A modular desk organiser of pie-wedge bins that swing out around a central post. Stack as many tiers as you like; a wide fillable ballast dish keeps it planted. Fully parametric OpenSCAD.
Boxes & storage / Keepsake boxes / Fantasy
Coffin Pencil Case — Magnetic Box with a Death's-Head Moth Lid
A toe-pincher coffin box for pens, markers and brushes. The lid is held by six pairs of hidden magnets buried mid-print, so no fastener is visible anywhere. Prints flat, no supports, one colour or two.
Boxes & storage / Organizers / Drawers
Parametric Apothecary Cabinet / Labelled Spice Rack
Wall-mountable N×M grid of cubbies, each holding a drop-in drawer with a raised label. Includes ready-to-print 2×3 English spice rack (Salt, Pepper, Sugar, Cinnamon, Rosemary, Curry). Edit the OpenSCAD source to change grid, cubby size, frame style, or label text.
Boxes & storage / Keepsake boxes / Geometric
Decorative Honeycomb Box (Parametric)
Open-top storage box with a hex pattern engraved on every wall — fully parametric OpenSCAD source.
Boxes & storage / Organizers / Tools & small parts
Haunted House Screw Organizer — 3 Drawer Floors, Crooked Mansard Roof
A crooked Victorian mansard house whose three floors are pull-out drawers for screws, nuts and bits. Five parts, no hardware, no glue, no supports; the pumpkin face and glowing windows are a second colour on the drawer fronts.
Boxes & storage / Organizers / Baskets
Lattice Basket — Parametric Desk Organiser
A 15 × 10 × 5 cm open-lattice basket with 45° crosshatch walls, solid corner columns, and a flat rim. No supports needed.
Boxes & storage / Organizers / Baskets
Parametric Stackable Storage Box (1×1 to 5×5)
Stackable storage drawers with stud-and-hole interlock — they tile sideways and stack vertically with each other. 25 ready-to-print sizes from 1×1 up to 5×5, with both door orientations for every rectangle, plus 2 height/fit specials. Parametric SCAD source included — change pitch, height, or footprint to derive any size you want (the SCAD goes well past 5×5).
Boxes & storage / Keepsake boxes / Fantasy
Potion of Holding — Twist-Lock Flask Organizer (2 sizes)
A fantasy potion flask that twist-locks apart into a wide-mouth bin with a 4-way divider — four sorted compartments for screws, bolts, beads, pills, or tiny treasure. A friction cork plugs the neck. Two sizes from the same design: a full-size desk organizer and a mini that fits inside a 2.7-inch gacha capsule.
Boxes & storage / Organizers / Tools & small parts
Tool Organizer — 4x4 Hex-Window Stand (parametric OpenSCAD)
Upright stand with 16 slots (4x4) for rasps, files, screwdrivers, pens, bits. Hex windows in the middle band let you see what's inside; solid top/bottom keep tools separated.
Boxes & storage / Organizers / Baskets
Stackable Lattice Basket — 4 Sizes + Parametric SCAD
Cross-stackable lattice baskets with cone-peg corner posts — any basket stacks onto any other basket. Four ready-to-print sizes from 5×5×5 cm cube up to a 20×12×8 cm tray, plus an optional cone-foot leg accessory. One open short side per basket so you can reach contents while the stack stays put. Parametric SCAD included — override basket_l/basket_w/body_h to derive any size; corner-post + peg geometry is shared so derived sizes still cross-stack with the printed ones.
Desk & office / Electronics / Stands
Stackable Server Rack — Tool-Free Mini-PC / NUC / SBC Shelf
A modular, tool-free rack for mini-PCs, NUCs, SBCs and other small servers. Each level is a honeycomb-vented floor on four fat corner posts; levels self-stack on cone pegs (no screws, no hardware) and four wide feet lift the whole tower off the desk for airflow. Print one floor per device, four feet once, stack as tall as you like. Parametric SCAD — resize for any box.
Boxes & storage / Organizers / Baskets
Truchet Bucket Box — 5-Compartment Organizer with Maze-Pattern Walls
A lidless 5-bucket organizer with a flowing Truchet-tile maze pattern engraved on all four walls. Great for beads, hardware, ball bearings, craft bits. No supports, prints flat. Fully parametric OpenSCAD source included — change bucket count, size, or pattern.
Boxes & storage / Keepsake boxes / Geometric
Bayonet Tube — Ø50 × 60 mm with Quarter-Turn Locking Caps
Cylindrical tube container with two IDENTICAL bayonet caps. Drop a cap on either end, push, twist 35°, locked. No hardware, no supports. Parametric OpenSCAD source included.
Around the home / Hooks
Bat Ceiling Hook — hangs by its own feet, head down, like a real bat
A roosting bat that hooks over a ceiling hook by its two toe-rings and gives you two open claw hooks at the bottom for cords, string lights or a planter. One part, no supports, no assembly.
Desk & office / Organizers / Pen Holders
Kangaroo Desk Organizer
Standing kangaroo with an open belly pouch that catches keys, AirPods, change, or small items. 52×85×120 mm tripod stance. Single-piece, no supports.
Desk & office / Electronics / Cables
Desk-Edge Cable Clamp — Clip-On with Printable Thumbscrew
A C-clamp that grips the edge of any desk and carries a cable through a C-shaped snap-in hook. Held in place by a fully printable knurled thumbscrew (plastic-on-plastic thread, no metal hardware, no tools). Three-part print.
Desk & office / Electronics / Cables
Desk Cable Rack — Pegs or Pole Variant (Parametric)
A simple desk-side cable rack to keep charging cables, headphones, and props off the floor. Two variants share the same base + back wall: a 6-peg version (each cable hooks over its own peg) and a single-pole version (cables drape over a full-length pole with a back-stop shelf). 200 × 150 × 100 mm. Prints flat on its back, no supports.
Desk & office / Organizers / Paper Notes
Stacking Letter / A4 Paper Tray — modular, honeycomb floor, 20 swappable nameplates
A classic 4-post stacking in-out tray for A4 or Letter paper, sized to fit a 256 mm bed. Paper sits landscape and overhangs the low open front so you can grab a sheet one-handed. Stack as many tiers as you print — corner pegs drop into the tier below. Comes with a pack of 20 clip-on nameplates (IN · OUT · TODO · URGENT · BILLS · CHAOS …) plus a blank one to write on. No screws, no glue, no supports.
Desk & office / Organizers / Modular
MagDock — Magnetic Desk & Shop Organizer Family
A family of small organizers that embed neodymium discs in their backs, so they snap onto ANY ferrous surface — printer frame, fridge, toolbox, filing cabinet, radiator. Hook, tray, tall caddy, pliers/scissors slots, and a bare puck. The magnets are sealed inside DURING printing (mid-print pause), so no caps and no glue. Every part prints flat on its back with NO supports.
Desk & office / Organizers / Modular
Moku Iris Box — Working Camera-Aperture Catch-All (Base Rail module)
A round fluted catch-all box for the Moku modular desk system whose lid is a WORKING 6-blade iris diaphragm — twist the knurled collar and the blades spiral open like a camera aperture onto the cavity (Ø48 mm) for clips, SD cards and coins. Same-plane pinwheel iris: 6 identical rigid blades on pivot posts, drive pins riding radial collar slots, snap-on collar, 1-minute no-order assembly, zero supports. Clips onto the host Base Rail by the reverse-measured foot interface. A remix of the Moku Base Rail by @SabreDesign / @Collecticraft.
Desk & office / Organizers / Paper Notes
Moku Memo Stand — Sloped Sticky-Note Writing Tray (Base Rail module, 3 sizes)
A sloped sticky-note writing tray that clips onto the Moku modular desk-system Base Rail. The pad sits on a 21° incline so the top sheet faces you — read it and write on it in place. Low front rim plus a centre finger-scoop to peel the top sheet; tall back and side rims keep the pad square. Three pad sizes (60 / 80 / 90 mm) and both rail orientations (slide on from the side or front/back) are bundled. Japandi fluted side faces to match the Moku look. A remix of the Moku Base Rail by @SabreDesign / @Collecticraft.
Jewelry & accessories / Jewelry displays
Moku Cantilever Watch Stand — open 'C' bracket + parametric engraved clock (Base Rail module)
A cantilever 'C' watch stand for a chunky sport/dive watch that clips onto the Moku modular desk-system Base Rail. A soft, near-rectangular bracket with smoothly filleted joints: a back spine carries a top arm that cantilevers forward over an open gap, its rest face CANTED ~20° SIDE-TO-SIDE so the watch leans on a dynamic diagonal. The watch sits centred over the base (so a heavy steel watch won't tip it off the rail); the bracelet drapes over the rounded front nose and hangs free, its end on the front shelf. The tall SPINE FRONT face — the back wall of the C, in full view through the opening — carries an ENGRAVED CLOCK FACE with PARAMETRIC hands (set the time in the SCAD, default 10:10) ringed by gear teeth. Every edge is rounded (Japandi). Prints PRINT-ON-END so the cantilever needs no supports and the rail foot prints as crisp vertical channels. A remix of the Moku Base Rail by @SabreDesign / @Collecticraft.
Desk & office / Electronics / Cables
Pretzel Cable Clip — Two-Colour Desk Cable Holder
A 58 x 44 mm pretzel-shaped desk clip for one small charging cable, with white salt accents. Flat print, no supports.
Around the home / Hooks
Radiator Hook — S-Hook for Towel Radiators (No Drilling, No Hardware)
A chunky plastic S-hook that slips over the top rail of a heated towel radiator and carries a towel, glove, bag, or keys on the bottom. No drilling, no adhesives, no metal hardware — one-piece print, flat on the bed, no supports.
Desk & office / Organizers / Pen Holders
Sunflower Pen Cup — Petal Crown + Gothic Quatrefoil Body
Tall pen / marker cup with an 18-petal sunflower crown at the rim and a brick-grid of gothic quatrefoils (cathedral-rose pattern) engraved into the body wall. Single open chamber, prints upright without supports.
Desk & office / Organizers / Pen Holders
Retro Tape Deck Desk Caddy — pen cups, phone dock, pull-out cassette drawer + swappable spine labels
A 1980s stereo cassette deck that is actually a desk organiser. Two 52 mm-deep pen cups, a catch-all tray, a tilted phone cradle with a cable pass-through, and a pull-out 'cassette' drawer whose spine label is a card you thread in sideways and swap. 9 spare captions on one sheet — or letter your own straight from the parametric OpenSCAD source. 3 printed parts, no hardware, no glue, no supports.
Desk & office / Electronics / Cables
USB Drive Caddy — Hex-Grill Open-Front Cubby
N×M open-front cubby for low-profile USB-C 'disc' drives. Drives lay flat and slide in from the front; ~4 mm sticks out for pinch removal. Decorative hex perforation on top + sides. Ships pre-rotated — open face prints UP, back wall on the bed, zero supports.
Desk & office / Organizers / Pen Holders
Wizard Tower Pen Holder — fantasy castle desk organizer
A squat stone wizard's tower that holds your pens and pencils. Crenellated battlement crown, spiral arrow-slit windows and a flared buttressed base; the bored centre well swallows a fistful of pens so they jut out the top like spires. Prints upright, no supports, fully parametric.
Around the home / Hooks
Cap Magnet Hook
A little magnetic hook shaped like a baseball cap — the curved brim is the hook. Two Ø10x5 mm neodymium discs sit sealed inside the flat back and stick it to any steel surface (fridge, locker, radiator, steel door frame). No screws, no supports. A screw-mount version is included too. Holds LIGHT things only.
Around the home / Hooks
Bag Hook for a Desk Edge or a Chair Back
Clamps onto a table edge, a desk lip or a chair backrest and gets the backpack off the floor. One part, no supports, no screws, no glue. Three sizes included — 20, 25 and 30 mm jaws — and a sprung tongue inside each takes up the slack below that, so between them they cover roughly 10 to 30 mm. A 7-minute fit-test coupon is included for every size so you can check the grip on your own table before printing the whole thing. The source file is included and fully parametric: change one number and you get a jaw for any thickness.