TAGGED
No hardware
8 designs tagged “No hardware”.
Bathroom / Makeup organizers
Moonwake Makeup Wardrobe — a 240 mm two-door cabinet with printed hinges and lift-off door bins
A 240 x 200 x 228 mm cabinet for makeup and hygiene: two engraved doors on four printed pins that swing to 160 degrees, four lift-off bins on the door panels, and two removable organizers inside for brushes, tubes and palettes. 13 parts, no hardware, no glue, no supports.
Board games / Find your game / Magic: The Gathering / Deck boxes & card care
Mana Press — screw press for Magic cards: flatten a bowed deck, brick a freshly sleeved one
A printed screw press for Magic cards. Two threaded posts, a yoke and two thumb nuts squeeze a stack flat overnight, or squeeze a freshly sleeved deck back into a brick that drops into its box. The posts ARE the screws — there is no hardware anywhere in the model, no screws, magnets or inserts. Height is set by stacking 12 mm pressure plates, which double as the WUBRG mana rainbow and each ship a named-solid 2-colour companion for AMS. An optional, experimental arc pair over-bends a curled foil past its set. 11 STLs, 6 printed parts, no supports, fully parametric OpenSCAD.
Boxes & storage / Lunch Boxes
Composition Book Lunchbox — a snack caddy shaped like a school notebook
A 150 x 105 x 52 mm lunch/snack caddy that looks like a marbled composition notebook. Print-in-place-style pin hinge (the pin prints too), no hardware, no supports, no glue. Three parts, three colours, and the colour split costs about 1.4 g of purge for the whole set.
Boxes & storage / Keepsake boxes / Nature
Rut Box — a keepsake box locked shut by two stags' antlers
A 108 x 62 x 84 mm hunting keepsake box with a 64 ml cavity. Four antler racks — two on the base, two on the lid — interleave when the box is closed, like two stags with their horns locked in the rut. A quarter turn sweeps the racks apart and releases a bayonet lock. No hardware, no supports, no glue.
Boxes & storage / Keepsake boxes / Geometric
Bayonet Tube — Ø50 × 60 mm with Quarter-Turn Locking Caps
Cylindrical tube container with two IDENTICAL bayonet caps. Drop a cap on either end, push, twist 35°, locked. No hardware, no supports. Parametric OpenSCAD source included.
Desk & office / Electronics / Cables
Desk-Edge Cable Clamp — Clip-On with Printable Thumbscrew
A C-clamp that grips the edge of any desk and carries a cable through a C-shaped snap-in hook. Held in place by a fully printable knurled thumbscrew (plastic-on-plastic thread, no metal hardware, no tools). Three-part print.
Around the home / Hooks
Radiator Hook — S-Hook for Towel Radiators (No Drilling, No Hardware)
A chunky plastic S-hook that slips over the top rail of a heated towel radiator and carries a towel, glove, bag, or keys on the bottom. No drilling, no adhesives, no metal hardware — one-piece print, flat on the bed, no supports.
Around the home / Hooks
Bag Hook for a Desk Edge or a Chair Back
Clamps onto a table edge, a desk lip or a chair backrest and gets the backpack off the floor. One part, no supports, no screws, no glue. Three sizes included — 20, 25 and 30 mm jaws — and a sprung tongue inside each takes up the slack below that, so between them they cover roughly 10 to 30 mm. A 7-minute fit-test coupon is included for every size so you can check the grip on your own table before printing the whole thing. The source file is included and fully parametric: change one number and you get a jaw for any thickness.