TAGGED
Office
16 designs tagged “Office”.
Desk & office / Organizers / Pen Holders
Amphora Pen Pot — Panathenaic Prize Amphora, Engraved Bands, No Supports
A Greek amphora as a desk pen pot: running-athlete frieze, Greek-key meander, ray and palmette bands, all engraved 0.7 mm into the curved wall. One part, prints upright with no supports. The foot is deliberately widened over the museum original so it does not tip when a pen leans.
Desk & office / Electronics / Cables
Desk-Edge Cable Clamp — Clip-On with Printable Thumbscrew
A C-clamp that grips the edge of any desk and carries a cable through a C-shaped snap-in hook. Held in place by a fully printable knurled thumbscrew (plastic-on-plastic thread, no metal hardware, no tools). Three-part print.
Desk & office / Electronics / Cables
Desk Cable Rack — Pegs or Pole Variant (Parametric)
A simple desk-side cable rack to keep charging cables, headphones, and props off the floor. Two variants share the same base + back wall: a 6-peg version (each cable hooks over its own peg) and a single-pole version (cables drape over a full-length pole with a back-stop shelf). 200 × 150 × 100 mm. Prints flat on its back, no supports.
Desk & office / Organizers / Pen Holders
Hedgehog Pen & Pencil Holder — your pens become the quills
A bald little hedgehog whose quills are YOUR pens and pencils. The smooth dome body has an angled fan of 11 blind bores drilled into its back; plug pens and pencils in and they radiate outward exactly like real quills. Dimple eyes and a snout finish the face. Prints belly-flat on the bed with zero supports — the dome is the top half of an ellipsoid so every wall leans inward going up. Single part, single colour, just print and load it up.
Desk & office / Reading & writing
Filigree Letter Opener — Flat Leaf Blade, No Supports
A 210 mm single-piece letter opener with a leaf-shaped chisel-ground blade and an ornamental filigree handle (quatrefoil rosette, flanking ovals, hang hole). Prints flat, no supports. PETG recommended for a stiff, durable blade.
Desk & office / Organizers / Paper Notes
Stacking Letter / A4 Paper Tray — modular, honeycomb floor, 20 swappable nameplates
A classic 4-post stacking in-out tray for A4 or Letter paper, sized to fit a 256 mm bed. Paper sits landscape and overhangs the low open front so you can grab a sheet one-handed. Stack as many tiers as you print — corner pegs drop into the tier below. Comes with a pack of 20 clip-on nameplates (IN · OUT · TODO · URGENT · BILLS · CHAOS …) plus a blank one to write on. No screws, no glue, no supports.
Desk & office / Organizers / Modular
Moku Iris Box — Working Camera-Aperture Catch-All (Base Rail module)
A round fluted catch-all box for the Moku modular desk system whose lid is a WORKING 6-blade iris diaphragm — twist the knurled collar and the blades spiral open like a camera aperture onto the cavity (Ø48 mm) for clips, SD cards and coins. Same-plane pinwheel iris: 6 identical rigid blades on pivot posts, drive pins riding radial collar slots, snap-on collar, 1-minute no-order assembly, zero supports. Clips onto the host Base Rail by the reverse-measured foot interface. A remix of the Moku Base Rail by @SabreDesign / @Collecticraft.
Desk & office / Organizers / Paper Notes
Moku Memo Stand — Sloped Sticky-Note Writing Tray (Base Rail module, 3 sizes)
A sloped sticky-note writing tray that clips onto the Moku modular desk-system Base Rail. The pad sits on a 21° incline so the top sheet faces you — read it and write on it in place. Low front rim plus a centre finger-scoop to peel the top sheet; tall back and side rims keep the pad square. Three pad sizes (60 / 80 / 90 mm) and both rail orientations (slide on from the side or front/back) are bundled. Japandi fluted side faces to match the Moku look. A remix of the Moku Base Rail by @SabreDesign / @Collecticraft.
Jewelry & accessories / Jewelry displays
Moku Cantilever Watch Stand — open 'C' bracket + parametric engraved clock (Base Rail module)
A cantilever 'C' watch stand for a chunky sport/dive watch that clips onto the Moku modular desk-system Base Rail. A soft, near-rectangular bracket with smoothly filleted joints: a back spine carries a top arm that cantilevers forward over an open gap, its rest face CANTED ~20° SIDE-TO-SIDE so the watch leans on a dynamic diagonal. The watch sits centred over the base (so a heavy steel watch won't tip it off the rail); the bracelet drapes over the rounded front nose and hangs free, its end on the front shelf. The tall SPINE FRONT face — the back wall of the C, in full view through the opening — carries an ENGRAVED CLOCK FACE with PARAMETRIC hands (set the time in the SCAD, default 10:10) ringed by gear teeth. Every edge is rounded (Japandi). Prints PRINT-ON-END so the cantilever needs no supports and the rail foot prints as crisp vertical channels. A remix of the Moku Base Rail by @SabreDesign / @Collecticraft.
Desk & office / Electronics / Stands
Monstera Phone Stand — cable-ready desk holder
A one-piece leaf phone stand with open charging access, corner ledges, and an 11 mm slot for slim cases.
Desk & office / Organizers / Paper Notes
Paper Block Desk Organizer — Sticky-Note Tray + Pen/Scissor Column + Slot
Three-zone desk organizer: thin slot for a phone or notebook on the left, a 90 × 90 mm paper-pad well in the middle (tall back, sloped sides, low front lip with finger-gap), and a pen/scissor column on the right with two-color pencil + scissors icon inlays.
Desk & office / Reading & writing
Two-Color Ruler — 15 cm + 20 cm (Parametric)
Simple two-color ruler with a sloped front edge so the ticks reach the precise measuring edge. Two lengths included (15 cm and 20 cm), each as a body + ink STL pair for AMS multi-filament printing.
Desk & office / Organizers / Pen Holders
Sunflower Pen Cup — Petal Crown + Gothic Quatrefoil Body
Tall pen / marker cup with an 18-petal sunflower crown at the rim and a brick-grid of gothic quatrefoils (cathedral-rose pattern) engraved into the body wall. Single open chamber, prints upright without supports.
Desk & office / Electronics / Cables
USB Drive Caddy — Hex-Grill Open-Front Cubby
N×M open-front cubby for low-profile USB-C 'disc' drives. Drives lay flat and slide in from the front; ~4 mm sticks out for pinch removal. Decorative hex perforation on top + sides. Ships pre-rotated — open face prints UP, back wall on the bed, zero supports.
Desk & office / Organizers / Pen Holders
Wizard Tower Pen Holder — fantasy castle desk organizer
A squat stone wizard's tower that holds your pens and pencils. Crenellated battlement crown, spiral arrow-slit windows and a flared buttressed base; the bored centre well swallows a fistful of pens so they jut out the top like spires. Prints upright, no supports, fully parametric.
Around the home / Hooks
Bag Hook for a Desk Edge or a Chair Back
Clamps onto a table edge, a desk lip or a chair backrest and gets the backpack off the floor. One part, no supports, no screws, no glue. Three sizes included — 20, 25 and 30 mm jaws — and a sprung tongue inside each takes up the slack below that, so between them they cover roughly 10 to 30 mm. A 7-minute fit-test coupon is included for every size so you can check the grip on your own table before printing the whole thing. The source file is included and fully parametric: change one number and you get a jaw for any thickness.