TAGGED
Desk organizer
14 designs tagged “Desk organizer”.
Bathroom / Makeup organizers
Cauldron Makeup Organizer — a bowl with no corners, no supports
A three-legged cauldron that sorts makeup, and the bowl is the whole idea: it is a truncated sphere, so there is no corner anywhere inside it for powder to pack into. A 2.6 mm wall runs into a 3 mm floor through a 4 mm fillet rather than a crease, and one wipe reaches every part of the inside. Brushes stand in it bristles-up and fan out against the curve; a 4-way cross drops in to quarter the bowl for jars, sponges, compacts and hair ties, and lifts out to leave a plain brush cup. The three legs are a separate trivet ring the bowl drops into on a 45 degree cone, because legs cast under the bowl print as a horizontal overhang between them. 3 parts, 92 x 90 x 77 mm assembled, 117 g, no supports, no hardware, no glue — assembly is dropping one part into another.
Bathroom / Makeup organizers
Dragon Wing Palette Rack — eyeshadow palettes on edge, no supports
An eyeshadow-palette rack whose fins are the finger bones of a dragon wing. Palettes stand on edge like books, so you read the spines and pull one out one-handed instead of excavating a stack. Five 16.5 mm slots take anything up to an 18 mm palette, with 100 mm of clear depth between the front rail and the back spine and a 76 mm shortest fin. Every segment of the fin profile is upward-facing, so a 112 mm tall part prints with ZERO supports. 1 part, 118 x 128 x 112 mm, no supports, no hardware, no assembly.
Bathroom / Makeup organizers
Frost Crystal Casket — makeup organizer, no supports
A block of glacier ice with a quartz cluster growing out of the back, and the cluster is the working part: all seven crystals are bored straight through, so a brush pushed into a shard stands bristles-up while its handle hangs in the box below — which is why a 120 mm and a 220 mm brush end up standing at the same height. Bores are cut to measured stock: Ø27 for mascara, two Ø23 that neck down to Ø14 so a lipstick rests on the shoulder, and four brush bores at Ø16 and Ø11. There is not one blind hole in the model and the well underneath is a single cavity with a 4 mm cove where the floor meets the wall, so nothing has a square corner to pack powder into. 3 parts, 132 × 114 × 100 mm, 298 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Great Helm Makeup Organizer — knight's helm, no supports
A 13th-century flat-topped great helm that is a makeup organizer on the inside. The crown is open and a lift-out liner drops onto the rim carrying the whole bore field, so brushes stand out of the helm like a crest: six brush bores go straight THROUGH so the handle hangs in the cavity and a 120 mm and a 220 mm brush stand at the same height, three tube bores (Ø27 mascara, two Ø23 lipstick) neck down instead of bottoming out, and an 88 × 24 mm palette slot rests a compact on an open 8 mm ledge. Not one bore is blind, so powder falls through into a smooth drum you tip out and rinse. 2 parts, 134 × 125 × 150 mm, 307 g, no supports, no hardware, no glue.
Bathroom / Makeup organizers
Medieval Well Makeup Organizer — no supports
A stone draw-well with a winding gantry, a gable roof and a bucket on a string — and a makeup organizer inside it. The coping stone is a lift-off plate carrying all 11 bores, and not one of them is blind: a brush handle hangs free down the shaft, a mascara rests in a 45° seat cone instead of bottoming out, and loose powder falls straight past into a rinse dish in the plinth. Cleaning is lift, lift, tip, rinse. 5 parts, Ø144 × 176 mm, 420 g, no supports, no hardware, no glue — just ~120 mm of twine for the bucket.
Desk & office / Organizers / Pen Holders
Owlbear Candle & Pen Holder — Chunky D&D Desk Sculpt
A round, grumpy owlbear (the classic owl-bear) as a chunky desk sculpt with a deep central bore — sized to hold a taper candle or a fistful of pens and pencils. Sculpted feathered belly, tufted ears, and a hooked beak. Prints like a vase: flat base, cavity opens up, no supports.
Desk & office / Organizers / Pen Holders
Amphora Pen Pot — Panathenaic Prize Amphora, Engraved Bands, No Supports
A Greek amphora as a desk pen pot: running-athlete frieze, Greek-key meander, ray and palmette bands, all engraved 0.7 mm into the curved wall. One part, prints upright with no supports. The foot is deliberately widened over the museum original so it does not tip when a pen leans.
Desk & office / Electronics / Cables
Desk Cable Rack — Pegs or Pole Variant (Parametric)
A simple desk-side cable rack to keep charging cables, headphones, and props off the floor. Two variants share the same base + back wall: a 6-peg version (each cable hooks over its own peg) and a single-pole version (cables drape over a full-length pole with a back-stop shelf). 200 × 150 × 100 mm. Prints flat on its back, no supports.
Desk & office / Organizers / Pen Holders
Hedgehog Pen & Pencil Holder — your pens become the quills
A bald little hedgehog whose quills are YOUR pens and pencils. The smooth dome body has an angled fan of 11 blind bores drilled into its back; plug pens and pencils in and they radiate outward exactly like real quills. Dimple eyes and a snout finish the face. Prints belly-flat on the bed with zero supports — the dome is the top half of an ellipsoid so every wall leans inward going up. Single part, single colour, just print and load it up.
Desk & office / Electronics / Stands
Keyboard Riser — Split, Dovetail-Joined, Parametric (60 / 100 / 180 mm Lift)
Open-frame stand that lifts a keyboard off the desk, leaving the space underneath clear. Three ready-to-print configurations: 60 and 100 mm lift for a 440 × 135 mm board, and 180 mm for a 313 × 123 mm 75 % board (Keychron K2 size). A 3 mm rim keeps the board from sliding off; a honeycomb deck spreads its weight. Too long for a 256 mm bed, so it splits into two halves that re-join with a drop-in dovetail key — no glue, no tools. Fully parametric: change one variable for any other board or height.
Desk & office / Organizers / Paper Notes
Stacking Letter / A4 Paper Tray — modular, honeycomb floor, 20 swappable nameplates
A classic 4-post stacking in-out tray for A4 or Letter paper, sized to fit a 256 mm bed. Paper sits landscape and overhangs the low open front so you can grab a sheet one-handed. Stack as many tiers as you print — corner pegs drop into the tier below. Comes with a pack of 20 clip-on nameplates (IN · OUT · TODO · URGENT · BILLS · CHAOS …) plus a blank one to write on. No screws, no glue, no supports.
Desk & office / Organizers / Paper Notes
Paper Block Desk Organizer — Sticky-Note Tray + Pen/Scissor Column + Slot
Three-zone desk organizer: thin slot for a phone or notebook on the left, a 90 × 90 mm paper-pad well in the middle (tall back, sloped sides, low front lip with finger-gap), and a pen/scissor column on the right with two-color pencil + scissors icon inlays.
Desk & office / Organizers / Pen Holders
Retro Tape Deck Desk Caddy — pen cups, phone dock, pull-out cassette drawer + swappable spine labels
A 1980s stereo cassette deck that is actually a desk organiser. Two 52 mm-deep pen cups, a catch-all tray, a tilted phone cradle with a cable pass-through, and a pull-out 'cassette' drawer whose spine label is a card you thread in sideways and swap. 9 spare captions on one sheet — or letter your own straight from the parametric OpenSCAD source. 3 printed parts, no hardware, no glue, no supports.
Desk & office / Organizers / Pen Holders
Twisted Ribbed Pen Cup — one part, no supports
A rounded-square desk cup whose whole surface is fine ribs turning through 90 degrees from the base to the rim. The cavity twists at the same rate as the shell, so the wall stays 1.6 mm the whole way up and nothing inside collects dust in a corner. 50 x 50 x 70 mm, 63 mm across the twisted corners, about 40 g, one part, no supports, no glue. Parametric OpenSCAD source included — twist angle, rib pitch, rib depth, corner radius and height are all named variables at the top.